India has more daylight than almost any country on earth, and yet a great many Indian homes are dim by day and lit by electricity from morning. Deep plans, small windows set for privacy, balconies enclosed into rooms, and buildings packed close together all cut the daylight that reaches the inside. The irony is sharp: in a land of relentless sun, people switch on lights at noon. Good daylighting design closes this gap — not by making windows as large as possible, which brings heat and glare, but by getting the right quantity of light, from the right direction, into the depth of the room.
Daylighting is also one of the clearest places where design meets well-being and energy. Rooms lit by daylight feel larger, calmer and healthier; natural light supports the body's daily rhythm; and a home that does not need artificial light by day uses less energy and costs less to run. This is why daylight has moved to the centre of green-building rating systems and energy codes. Yet the subject is often reduced to a vague instruction to add more glass, which ignores the two things that decide whether daylight is pleasant or punishing: direction and control.
This article explains how daylight is measured and targeted, using the daylight factor and the window-to-floor ratio; how orientation changes the character of light in Indian conditions; and how to let light deep into a room while keeping heat and glare out. It covers the standards and rating systems that bear on daylight in India and the practical moves — window placement, light shelves, courtyards, glazing choice and glare control — that make a home bright by day without becoming an oven.
Measuring daylight: the daylight factor
The most useful single measure of daylight is the daylight factor. It is the indoor daylight level at a point expressed as a percentage of the daylight available outside at the same moment under an overcast sky. If the inside of a room reads one-fiftieth of the outdoor level, its daylight factor is 2 per cent. The measure is powerful because it is independent of the weather: it describes the building, not the day. As a working guide, an average daylight factor of about 2 per cent makes a living space feel adequately daylit, a kitchen or study wants more — around 3 to 5 per cent for close work — while a figure below about 1 per cent reads as gloomy and will need artificial light even at midday. These are design targets drawn from standard practice, not a single legal threshold.
The window-to-floor ratio and the one-tenth rule
The daylight factor is calculated, but a simpler rule gets a design started: the window-to-floor ratio, the area of glazing as a fraction of the floor area of the room it serves. Indian practice, echoing the National Building Code, uses a long-standing rule of thumb that the openings for light and ventilation in a habitable room should be at least about one-tenth of the floor area — more in hot, deep rooms. So a 12 square metre bedroom wants at least roughly 1.2 square metres of window, and a living room that must feel bright wants more, often one-sixth to one-fifth of its floor area in glass. The ratio is only a start, because where the glass sits matters as much as how much there is: a tall window reaching near the ceiling throws light far deeper into a room than a wide, low one of the same area.
| Room | Window-to-floor ratio (guide) | Daylight factor target | Note |
|---|---|---|---|
| Living room | 1/6 to 1/5 | ≈ 2% | Bright, sociable; glare must be controlled |
| Bedroom | 1/8 to 1/6 | ≈ 1.5–2% | Comfortable; privacy shapes placement |
| Kitchen | 1/6 to 1/5 | ≈ 3–5% | Task light over the counter |
| Study / home office | 1/6 to 1/5 | ≈ 3–5% | Even light, no screen glare |
| Bathroom | 1/10 (minimum) | ≈ 1% | Light plus ventilation; privacy glazing |
| Staircase / lobby | 1/10 | ≈ 1–2% | Safety; a borrowed-light opening helps |
Direction: the character of light in India
In the northern hemisphere the four orientations give quite different light, and in India's strong sun the differences are magnified. North light is the designer's favourite: soft, cool, even and almost free of direct sun and glare, ideal for studies, art and anywhere steady light is wanted. South light is generous and, crucially, easy to shade — the high midday sun is cut by a modest horizontal projection, making south a controllable, valuable aspect. East light brings welcome, gentle morning sun that is warm but low in heat. West light is the difficult one: low, hot afternoon sun that drives straight into a room under any ordinary overhang, producing the worst glare and heat gain of the four. A good plan puts living and working rooms to the north, south and east, keeps the harsh west for service spaces or shades it heavily, and never relies on a flat overhang to tame a west window.
Getting light deep into a room
A single side window lights a room to roughly twice the height of its head — about four metres for a standard window — and no further, which is why deep rooms stay dim at the back no matter how wide the glass. Several moves push light deeper. Raising the window head towards the ceiling throws light further in. A light shelf — a horizontal baffle across the window at about door-head height — shades the lower glass from direct sun while bouncing light off its top surface onto the ceiling and far into the room. Light, matt, pale ceilings and upper walls act as reflectors and carry that bounced light. Where a room is deep or internal, a second source transforms it: a skylight, a clerestory window high in the wall, a light well or an internal courtyard, or borrowed light through a glazed internal partition or a jaali from a brighter adjoining space.
Glazing: light in, heat out, glare down
Glass is not neutral, and its specification decides whether daylight comes with heat and glare. Three numbers matter. Visible light transmittance (VLT) is the fraction of daylight the glass lets through — high VLT for a bright room, lower for glare control. The solar heat gain coefficient (SHGC) is the fraction of solar heat admitted — low SHGC is wanted in hot India to keep heat out. The U-value measures heat conduction and matters most for air-conditioned rooms. The designer's goal in Indian conditions is high visible light with low solar heat — a combination delivered by solar-control and low-emissivity (low-E) coated glass, which passes daylight while reflecting much of the heat. Ordinary clear glass admits both light and heat freely; heavily tinted glass cuts heat but also dims the room and distorts colour, so a good low-E glass usually beats a dark tint for a room that must stay bright and cool.
| Glazing | Visible light (VLT) | Solar heat (SHGC) | Best use |
|---|---|---|---|
| Clear single glazing | High (~0.8) | High (~0.8) | Shaded, north windows |
| Tinted glass | Lower | Moderate | Glare cut where some dimming is fine |
| Solar-control / low-E | High | Low | Sunny aspects; bright and cool |
| Double glazing (low-E) | High | Low | Air-conditioned rooms; comfort and quiet |
| Frosted / obscured | Moderate | Varies | Bathrooms; light with privacy |
Daylight, the codes and green ratings
Daylight sits inside India's building and energy framework in several places. The National Building Code of India 2016, in Part 8 on building services, sets requirements for natural light and ventilation and carries the long-standing rule that habitable-room openings should be adequate for light, commonly read as the one-tenth-of-floor-area guide. The Energy Conservation Building Code addresses daylight indirectly, by limiting solar heat gain and rewarding designs that cut artificial lighting. Green-building rating systems go furthest: GRIHA and IGBC both award credits for daylighting a defined share of the regularly occupied floor area to a target daylight factor, which has pushed daylight from an afterthought to a measured design goal. For a home, the lesson is simple — daylight is now something to design and check against a number, not to leave to chance.
Shading sized to the orientation
Shading is not one device but a family, and each orientation wants a different member of it. A horizontal projection — a chhajja, a balcony slab, a deep reveal — works on the south, where the sun is high through the hottest hours and a modest overhang casts the window into shade. The depth is set by a simple ratio: a projection roughly half the height of the window below it shades most of the midday summer sun on a south face, while still letting the lower winter sun reach in. The west and east are harder, because the sun there is low in the sky and drives in under any horizontal overhang; here the answer is vertical — fins, louvres, a jaali screen, planting or shutters — or shading placed entirely outside the glass.
The order of preference is always the same: stop the sun outside the glass wherever possible, because once solar heat has passed through the glazing it is already inside the room and must then be cooled away at a cost. This is why an external chhajja, pergola or screen beats an internal blind for controlling heat, and why a blind, however handsome, is really a glare device rather than a heat one. Movable shading — adjustable louvres, external roller shades, even a deciduous creeper that shades in summer and drops its leaves in winter — gives the best of both, admitting winter sun and excluding summer sun from the same opening.
| Orientation | Best shading | Why |
|---|---|---|
| South | Horizontal chhajja / overhang | High midday sun is easily cut |
| West | Vertical fins, jaali, external shade | Low afternoon sun defeats overhangs |
| East | Vertical or movable shade | Low morning sun, gentler heat |
| North | Little or none needed | No direct sun to control |
| Skylight / roof | External louvre or diffuser | Overhead sun is intense; diffuse it |
Surfaces inside the room are part of the daylighting system too, because daylight that enters is only useful if it is carried into the depth of the room rather than absorbed at the window. Pale, matt finishes on ceilings and upper walls reflect light far into the plan; dark floors and walls swallow it. The table below gives the rough light reflectance that different finishes return. It explains why a daylight strategy always pairs generous, well-placed glazing with light-coloured, non-glossy interior surfaces, and why a room painted in deep, fashionable dark tones needs noticeably more glass to feel as bright as a pale one. A bright room is as much about what the light lands on as about how much comes in through the window.
| Surface finish | Approx. light reflectance | Effect on daylight |
|---|---|---|
| White / off-white matt | 70–85% | Carries light deep into the room |
| Light pastel | 50–70% | A good secondary reflector |
| Mid-tone paint | 30–50% | Neutral; some light is lost |
| Timber / medium wood | 20–40% | Warm, but absorbs light |
| Dark paint / stone | 5–20% | Absorbs light; room feels dim |
Where a room is deep or internal and no window will reach it, the daylight has to be brought from above or borrowed from alongside. A skylight or roof light is the most powerful source of all, delivering several times the light of a side window of the same area, though it must be shaded or diffused against the overhead sun. A light well or internal courtyard carries daylight down through a building and has cooled and lit Indian homes for centuries. And borrowed light — a glazed internal partition, a fanlight over a door, a jaali between a bright room and a dim one — spreads daylight from where there is plenty to where there is none, at almost no cost in energy. These moves, planned early, are what let a deep plan stay bright without a wall of west-facing glass.
Where daylighting is heading
Daylight is moving from rule of thumb to simulation. Designers increasingly model a home's daylight before it is built, using software that predicts the daylight factor and the hours of useful daylight across the year, so that window size, placement and shading can be tuned on screen rather than regretted on site. Dynamic and switchable glazing, which can change its tint to control glare and heat through the day, is moving from commercial buildings towards homes. And daylight is being designed hand in hand with health, as evidence grows that natural light and a view support sleep, mood and productivity. For Indian homes the direction is encouraging: more daylight, better controlled, with less heat and less glare, and with electricity reserved for after dark. The principles in this article — the right amount of light, from the right direction, under control — are exactly what these tools are being used to deliver.
None of this needs to be expensive. Many of the most effective daylighting moves — raising a window head, keeping a ceiling pale, placing a glazed panel over an internal door, borrowing light through a jaali, choosing a better glass — cost little or nothing extra if they are decided while the home is still on the drawing board. The expensive mistakes are the ones discovered later: the deep room that is dark at the back, the west window that cannot be used in the afternoon, the internal bathroom with no daylight at all. Daylighting rewards forethought far more than budget, which is exactly why it belongs at the start of a design rather than the end.
Rules for daylighting a home
- Aim for an average daylight factor around 2% in living spaces, and 3–5% where close work happens.
- Start sizing windows at about one-tenth of floor area for light, and more for rooms that must feel bright.
- Put living and working rooms to the north, south and east; keep the harsh west for service spaces or shade it heavily.
- Raise window heads towards the ceiling to throw light deeper into the room.
- Use a light shelf on sunny aspects to bounce light in and shade the lower glass at once.
- Keep ceilings and upper walls pale and matt so they reflect daylight to the back of the room.
- Bring a second source — skylight, clerestory, courtyard or borrowed light — into any deep or internal room.
- Specify solar-control or low-E glazing for high visible light with low solar heat; avoid heavy tints that dim the room.
- Design shading and glazing together with the window, never as an afterthought added later.
Frequently asked questions
What is a good daylight factor for a home?
About 2 per cent average for living spaces reads as comfortably daylit, and 3–5 per cent suits kitchens and studies where close work happens. Below roughly 1 per cent a room feels gloomy and needs artificial light even at midday. These are design targets from standard practice.
How big should a window be for natural light?
A useful starting rule is window area of at least about one-tenth of the room's floor area, echoing NBC guidance, and more — often one-sixth to one-fifth — for rooms that must feel bright. Placement matters as much as size: a tall window reaching near the ceiling lights a room far deeper than a low, wide one.
Which direction is best for windows in India?
North gives soft, even, glare-free light and is ideal for studies and steady work. South is generous and easy to shade. East brings gentle morning sun. West is the problem aspect — low, hot afternoon sun that defeats a flat overhang — and is best avoided for living rooms or shaded heavily with fins or a jaali.
How do you bring daylight into a deep or internal room?
A single side window only lights to about twice its head height, so a deep or internal room needs a second source: a skylight, a clerestory window high in the wall, a light well or internal courtyard, or borrowed light through a glazed partition or jaali from a brighter adjoining room. Pale ceilings help carry the light.
Does more glass mean better daylighting?
Not by itself. Large unshaded glass, especially to the west, brings heat and glare that make a room uncomfortable and costly to cool. Good daylighting balances quantity with direction and control — the right amount of light, well placed, with solar-control glazing and proper shading.
Sources & standards
- National Building Code of India 2016, Part 8 — Building Services (natural lighting and ventilation)
- Bureau of Indian Standards — IS 2440: Guide for daylighting of buildings, and SP 41: Handbook on functional requirements of buildings
- GRIHA (Green Rating for Integrated Habitat Assessment) — daylighting criteria and credits
- Bureau of Energy Efficiency — Energy Conservation Building Code (ECBC), fenestration and solar heat gain provisions
- IGBC (Indian Green Building Council) — daylighting credit under its green homes rating
- Neufert, Architects' Data, and Time-Saver Standards — daylight factor and window-to-floor guidance
- Price ranges: indicative October 2026 estimates — confirm locally before budgeting




