← All articles

Materials & Finishes · 09 Nov 2026 · 22 min read

SPC vs Laminate Wooden Flooring in India

SPC vs Laminate Wooden Flooring in India — cover

Walk into any flooring showroom in Surat, Ahmedabad, Pune or Bengaluru and the same two planks will be pushed forward: laminate and SPC. Both click together without glue, both carry a photograph of oak or walnut on their faces, and both are sold as the smart, affordable alternative to real hardwood and to cold vitrified tiles. To a homeowner standing on the display floor, they feel almost identical underfoot. That resemblance is exactly what causes the wrong floor to be bought, because the two are built on opposite principles and fail in opposite ways.

Indian homes put wooden floors under pressure that European catalogues rarely mention. Floors here are swabbed with a wet mop most days, often with a bucket of water and a cloth rather than a barely damp microfibre pad. The monsoon pushes indoor humidity high for months. Kitchens and washbasin zones see splashes, and children and grandparents move between rooms in a house where water is simply part of cleaning. A wooden-look floor that cannot tolerate water is the single most common flooring regret, and it is almost always a laminate that was laid where an SPC or a tile belonged.

This article separates the marketing from the construction. It explains what each floor is actually made of, layer by layer; how they behave with water, scratches, dents, heat and sound; how they are installed and where installation goes wrong; what they cost in indicative October 2026 rupees; and which rooms each one suits. The aim is that a reader can stand on that showroom floor and know, from the room they are buying it for, which plank to point at.

Where these floors came from

Wooden-look flooring did not begin with plastic. For most of the twentieth century a wooden floor in India meant either site-laid teak or sheesham planks in grander homes, or imported parquet and linoleum in a handful of colonial buildings. These were beautiful but slow, skilled and expensive, and they needed sanding and polishing to stay presentable. The idea of a factory-made plank that any carpenter could click together is recent, and it arrived in two waves.

Laminate came first. The modern laminate floor was invented in Sweden in 1977 and reached India in strength through the 1990s and 2000s as imported and then locally distributed click planks. It solved the speed and cost problem: a printed decorative layer over a dense wood-fibre core gave a convincing timber look at a fraction of hardwood's price, installed in a day without polish. For two decades it was the default upgrade from tiles. Its weakness — the wood-based core — was tolerated because nothing better existed at the price.

SPC is the second wave. The rigid stone-polymer composite plank emerged commercially in the 2010s and became mainstream in Indian homes through the 2020s, precisely because it answered laminate's water problem. By replacing the wood-fibre core with a dense mineral-and-PVC composite, SPC offered a plank that looked the same but shrugged off water, humidity and temperature swings. The history, then, is simple: both floors chase the same goal — the look of wood without its cost or upkeep — and SPC is the newer answer to the oldest complaint about laminate.

Fig. 1 — Wooden-look floors through time 1900s–50sparquet, linoleumsite-laid wood 1977laminate inventedSweden 1990s–2000slaminate in IndiaHDF click planks 2010sSPC rigid corestone-polymer 2020sSPC mainstreamin Indian homes The goal never changed: the look of wood, without its cost or its polishing. Only the core material changed — from solid timber, to a printed wood-fibre board, to a rigid mineral-and-PVC composite that ignores water.
Fig. 1 — Wooden-look floors through time

What each floor is actually made of

The feel of the surface is the same because the top two layers are the same idea in both floors: a high-resolution printed image of timber, protected by a transparent wear layer. The difference that matters is hidden underneath, in the core. Understanding the stack tells a buyer almost everything about how the floor will behave once it is laid and lived on.

Laminate: a wood-fibre sandwich

A laminate plank is built around a core of high-density fibreboard, or HDF — wood fibres bonded under heat and pressure into a dense board, typically 6 to 12 mm thick. On top sits a decorative paper printed with the wood grain, and over that a melamine overlay that forms the wear layer. The resistance of that overlay to abrasion is graded by an AC rating from AC1 to AC5; for Indian homes an AC4 or AC5 plank is sensible in living areas. Underneath the core is a balancing backer that stops the plank curling. The whole thing is excellent until water finds a joint: HDF is wood, and wood swells. Once the edges of a laminate plank swell, they do not shrink back, and the joint stays raised forever.

SPC: a rigid mineral core

An SPC plank — stone plastic, or stone polymer, composite — replaces the wood-fibre core with a rigid board made mostly of finely ground limestone mixed with PVC and stabilisers. This core is dense, hard and, crucially, waterproof: it does not absorb water, so submersion or a wet mop does not swell it. The same printed decor film and a UV-cured wear layer sit on top, and most SPC planks come with a thin IXPE or EVA foam pad already attached to the underside for a little warmth and sound damping. The trade-off for that stability is that the floor is harder and colder underfoot than laminate, and a dropped knife or a dragged chair leg can still dent the softer wear layer even though the core beneath is tough.

Fig. 2 — What is inside each plank LAMINATE SPC (rigid) melamine wear layerdecor paper (AC rated) HDF wood-fibre core6–12 mm — swells if wet balancing backer UV + weardecor film stone-polymercore — waterproof IXPE pad (attached) 8–12 mm 4–7 mm The top two layers are the same idea in both floors. The core decides everything: wood-fibre that swells, or mineral-filled PVC that does not. SPC is thinner and harder; laminate is thicker, warmer and softer underfoot.
Fig. 2 — Layer construction compared (section)

How they compare where it matters

A fair comparison looks past the showroom and asks how each floor behaves over years of ordinary Indian use. Water is the headline difference, but it is not the only one. Laminate is thicker, so it feels warmer and quieter and more forgiving to stand on; SPC is thinner and rigid, so it is more stable against heat and humidity but harder and colder. Scratch resistance depends on the wear layer in both, while dent resistance favours the dense SPC core. The table below sets the two side by side on the measures a household actually notices.

MeasureLaminateSPCWhich wins
Water at the jointsSwells permanently once it penetratesUnaffected; core is waterproofSPC clearly
Feel underfootWarmer, softer, quieterHarder, colder, more solidLaminate
Dent from a dropped objectDents the HDF; can chipDense core resists dents betterSPC
Scratch resistanceAC4–AC5 overlay is very hardGood, but softer wear layerLaminate edges it
Heat and humidity stabilityCan gap or peak in swingsVery stable; ignores humiditySPC
Subfloor flatness neededTolerant with a thicker underlayRigid; shows lumps if subfloor unevenLaminate

Two of these rows surprise people. First, laminate often wins on pure surface scratch resistance because a top-grade melamine overlay is genuinely tough; SPC's advantage is the core, not the skin. Second, SPC is less forgiving of an uneven subfloor than laminate, because a rigid plank bridges a hollow and can click apart or rock, whereas a slightly flexible laminate with a soft underlay settles over minor undulations. Neither floor, however, forgives standing water at the joints the way a tile does — SPC resists far better, but a pool left for hours can still creep under planks and lift the attached pad.

Installation: where good floors go wrong

Both floors are floating floors: the planks lock to each other, not to the slab, and the whole field floats as one sheet over an underlay. That is why installation detail, not the plank itself, causes most failures. Three rules decide whether a floating floor stays flat and quiet for a decade: it must be acclimatised before laying, it must have a continuous expansion gap around every fixed edge, and large areas must be broken by transition strips. Skipping any one of them is how a correctly specified floor still ends up peaking, gapping or ticking.

Acclimatisation means leaving the planks, in their boxes, flat in the room for 24 to 48 hours so the material reaches the room's temperature and humidity before it is locked together. The expansion gap — typically 8 to 12 mm — is left all around the room, at every wall, pillar and pipe, and is hidden later under the skirting and beading. A floor laid tight to the walls has nowhere to move when it expands in summer, so it lifts in the middle. And because a continuous run can only grow so much before the gap is used up, long or L-shaped areas are split at doorways with a transition profile.

Fig. 3 — Floating floor plan: gap and run limits 8–12 mm expansion gap (hidden under skirting) plank run≤ 12 m laminate≤ 15 m SPC planks float as one sheet transition strip at every doorway splits long or L-shaped runs Acclimatise planks flat in the room 24–48 hours first. Leave the gap at every wall, pillar and pipe. A floor laid tight to the walls has nowhere to grow in summer, so it peaks in the middle — the most common floating-floor fault.
Fig. 3 — Floating floor: expansion gap and run limits (plan, mm)

The click joint itself is worth seeing once. Most planks use an angle-in profile: the tongue of a new plank is held at a slight angle against the groove of the laid one and folded down flat to lock. A good joint snaps home with no gap and no step. The underlay below matters too — a foam or cross-linked pad that evens out the subfloor, damps footstep sound and, under laminate, must sit on a plastic sheet moisture barrier over any concrete slab that could wick damp. The figure below shows the joint and the common plank sizes stocked in India.

Fig. 4 — Click joint and standard plank sizes A — Angle-in click joint laid planknew plank folds down Tongue meets groove at an angle, then foldsflat to lock — no glue, no gap, no step. B — Common plank (plan) 1200–1220 length 180–200 wide Laminate total 8–12 mm thick;SPC total 4–7 mm thick. Wide-plank and herringbone formatsexist in both at a premium. Under laminate on a concrete slab, lay a plastic sheet moisture barrier first, then the foam underlay, then the planks. Most SPC arrives with an IXPE pad attached, so it usually needs only a thin underlay or none.
Fig. 4 — Click joint and plank sizes (section and plan, mm)

What each floor costs

Prices below are indicative October 2026 ranges for a supplied-and-installed floor per square foot in Indian metro and tier-2 cities, excluding GST, and they move with brand, wear-layer grade, plank format and quantity. As a working guide, SPC runs about ₹120–250 per sq ft installed, and laminate about ₹80–180 per sq ft installed; thin builder-grade laminate can be found lower, and thick wide-plank SPC with a heavy wear layer runs higher. Underlay, skirting, transition strips and subfloor levelling are usually quoted on top, so a like-for-like comparison must put the all-in number against the all-in number, not plank against plank.

Item (per sq ft, installed)LaminateSPCNote
Plank, supplied and laid₹80 – ₹180₹120 – ₹250Wear-layer grade drives the top of each band
Foam / moisture underlay₹8 – ₹25₹0 – ₹15SPC often has an attached pad
Skirting / beading (per rft)₹40 – ₹120₹40 – ₹120Matching or paintable profiles
Transition strips (each)₹250 – ₹900₹250 – ₹900One at each doorway
Subfloor levellingOnly if unevenMore often neededSPC demands a flatter base
Realistic all-in band₹100 – ₹220₹140 – ₹290Varies with site and brand

Which floor belongs in which room

The right answer is almost always decided by water and by how the room is used, not by the plank's appearance. Bedrooms, drawing rooms and studies are dry, low-splash spaces where warmth and quiet are valued — laminate's natural home. Kitchens, utility areas, washbasin zones and any room mopped heavily or exposed to humidity are SPC's home, because the rigid waterproof core tolerates what laminate cannot. Genuinely wet areas — bathrooms with open showers, balconies in the rain — belong to tile or stone, not to either plank. The table turns this into a room-by-room rule.

RoomFirst choiceWhy
Master and children's bedroomsLaminateDry, low splash; warmth and quiet are wanted
Drawing and living roomLaminate or SPCLaminate for warmth; SPC if mopped wet daily
Study, home office, dressing roomLaminateDry, comfortable underfoot, quiet
Kitchen and utilitySPCSplashes and heavy mopping; core is waterproof
Washbasin and vanity zonesSPCStanding splashes; humidity nearby
Bathroom, open balconyNeither — tile or stoneStanding water defeats any floating plank

One more practical point ties the choice to the house, not just the room. Homes that are swabbed with a genuinely wet mop every single day — a very common habit across India — tilt the whole decision towards SPC even in dry rooms, simply because the daily water load is higher than the European testing assumes. Homes that clean with a well-wrung or barely damp mop can enjoy laminate's warmth across all the dry rooms with confidence. Aaditya Interior's usual approach is to zone a home: laminate through the sleeping and living wing, SPC through the kitchen-and-utility wing, and tile in the wet rooms.

Where wooden flooring is heading

Three shifts are already visible. First, SPC is steadily displacing laminate in the mass market as its price falls and its realism improves, so the two bands are converging and the water advantage is winning more rooms. Second, wear layers and surface textures are getting better: deeper embossing registered to the printed grain, matte finishes that hide dust, and tougher UV coatings that resist both scratch and the harsh cleaning common in Indian homes. Third, hybrid and WPC (wood-plastic composite) cores are appearing between the two — a little warmer and quieter than mineral SPC, still waterproof — aiming to give laminate's comfort with SPC's resilience.

What will not change is the logic a buyer must apply. A wooden-look floor is a system of layers, and the core decides its fate. Whatever the brand on the box or the name of the oak printed on the face, the sensible questions stay the same: what is the core, how thick is the wear layer, how is it being installed, and does this room see water. A reader who holds those four questions will choose correctly from whatever the showroom offers next year as readily as from what it offers today.

Day-to-day care is easy for both floors, and it is one more place where the water difference quietly shows. Both are swept or vacuumed and then cleaned with a well-wrung damp mop; the real difference is how much water each tolerates in that mop and how quickly a spill must be dealt with before it reaches a joint.

Care taskLaminateSPCNote
Routine cleaningWell-wrung damp mop onlyDamp mop; tolerates more waterNever flood either floor
A spillWipe at once before it reaches jointsWipe soon; the core is unaffectedJoints are the weak line in both
Scratches and chairsFelt pads; lift furniture, never dragFelt pads; softer wear layerPrevention beats repair on both
A worn-out surfaceReplace planks; cannot be sandedReplace planks; cannot be sandedNeither refinishes like solid wood

Nine rules for choosing and laying a wooden-look floor

  • Choose by the room's water load first, the plank's appearance second — water decides, looks follow.
  • Put laminate in dry bedrooms, studies and living rooms; put SPC in kitchens, utilities and splash-prone zones.
  • Never lay either floor in a bathroom with an open shower or an uncovered balcony — use tile or stone there.
  • For living areas, insist on an AC4 or AC5 laminate, or an SPC with a wear layer of at least 0.3 mm (12 mil).
  • Acclimatise the planks flat in the room for 24–48 hours before a single joint is clicked.
  • Leave an 8–12 mm expansion gap at every wall, pillar and pipe, and hide it under the skirting.
  • Split long or L-shaped areas with a transition strip at doorways so the floor can expand.
  • Lay a plastic moisture barrier under laminate on any concrete slab; check the subfloor is flat for SPC.
  • Compare quotes all-in — plank, underlay, skirting, strips and levelling — not plank price against plank price.

Frequently asked questions

Is SPC flooring fully waterproof?

The SPC core is waterproof and will not swell from a wet mop, splashes or short-term standing water, which is why it suits kitchens and utility areas. But the joints are not sealed like tile grout, so a large pool left for many hours can still creep under the planks. SPC resists water far better than laminate; it is not a substitute for a properly waterproofed and sloped bathroom floor.

Which is cheaper, SPC or laminate?

Laminate is usually the cheaper plank, at about ₹80–180 per sq ft installed against SPC's ₹120–250, in indicative October 2026 rupees. The gap is narrowing as SPC prices fall. For a dry room the cheaper laminate is fine; for a wet-prone room the slightly dearer SPC avoids a costly swelling failure, so it is the better value there.

Can wooden flooring be laid over existing tiles?

Yes. Both floors are floating floors and can be laid over sound, well-bonded existing tiles, which is one of their big advantages during a renovation. The tile surface must be clean, flat and dry; wide grout lines may need filling, and SPC in particular needs a flat base. Laying over tiles raises the floor level slightly, so door bottoms and thresholds must be checked.

Does SPC feel cold and hard underfoot?

SPC is harder and cooler underfoot than laminate because its core is mineral and it is thinner, with only a slim attached pad. In bedrooms where comfort matters, laminate feels warmer and softer. Where SPC is chosen for its water resistance but comfort is wanted, a thicker SPC, a WPC-core plank or an area rug closes much of the gap.

How long do these floors last?

With correct installation and sensible care, a good laminate lasts roughly 10 to 15 years in a home and a good SPC a similar span or a little more, with the wear layer and the installation quality mattering more than the plank's name. Neither can be sanded and refinished like solid wood; when the wear layer is gone the floor is replaced, which is simple because it floats.

Sources & standards

  1. Bureau of Indian Standards and National Building Code of India 2016, Part 6 (structural design) and Part 8 (building services): subfloor, moisture and interior finish provisions
  2. EN 13329 — laminate floor coverings: specification, requirements and the AC abrasion classes (AC1–AC5)
  3. EN 16511 — modular multilayer (rigid) floor coverings with a wear layer, covering SPC-type rigid planks
  4. Ernst and Peter Neufert — Architects' Data: floor build-ups, underlays and expansion allowances
  5. Joseph De Chiara and Michael Crosbie — Time-Saver Standards for Building Types and interior finishes
  6. Flooring manufacturer technical data sheets (generic): wear-layer thickness in mil, acclimatisation and expansion-gap guidance
  7. Price ranges: indicative October 2026 estimates for supplied-and-installed floors — confirm with a local dealer before budgeting
Discuss your project