← All articles

History of Design · 06 Nov 2026 · 21 min read

The Story of Athangudi Tiles: Making, Patterns and Modern Use

The Story of Athangudi Tiles: Making, Patterns and Modern Use — cover

Among the many materials that give a Chettinad house its character, one is still made the same way it always was, in the same place, by hand: the Athangudi tile. Named after the small village of Athangudi in the Chettinad region of Tamil Nadu, these are handmade cement tiles, poured and set rather than fired, each one carrying a coloured pattern locked into its surface. They have outlived the mansions that first used them because they are genuinely good: cool underfoot, long-lasting, repairable, and quietly beautiful in a way machine-made tiles struggle to copy.

For a long time the Athangudi tile was a regional secret, specified only by those restoring Chettinad houses. Over the last two decades it has travelled — into boutique hotels, cafes, designer apartments and heritage-minded homes across India — because it answers a real desire for a floor that feels handmade and rooted rather than printed and perfect. But it is often specified badly: laid on an uneven bed where it cracks, grouted with wide dark lines that fight the pattern, or left unsealed so it stains. This article explains what the tile is, how it is made, how to choose and lay it, and what it costs, so that admiration turns into a floor that lasts.

The key fact to hold onto is this: an Athangudi tile is not a ceramic or a vitrified tile. It is a cement product, cured with water, finished with a glass plate. That changes everything about how it is chosen, laid, grouted and maintained. Treat it like a glazed ceramic tile and it will disappoint; treat it as what it is — a handmade cement tile in the tradition of encaustic and hydraulic cement tiles used worldwide — and it will reward.

What an Athangudi tile is

An Athangudi tile belongs to the worldwide family of cement tiles — the same broad family as the encaustic and hydraulic tiles found in old European and colonial buildings. It is made of cement, fine sand or stone powder, and mineral oxide pigments, pressed and cured rather than fired in a kiln. Because it is never fired, it is made at village scale with simple tools: a glass plate, a metal frame, and a thin patterned stencil. The pattern is not printed on top; it is cast into the top layer, so it goes a few millimetres deep and does not wear off the way a surface print does.

The surface sheen — soft, slightly uneven, almost waxy — is the tile's signature, and it comes from the glass. Each tile is cast face-down against a clean sheet of glass, so the finished face takes on the smoothness of the glass without any glaze or polish. That is why no two tiles are identical and why the surface has a gentle, hand-made life to it. It is also why the tile is cool to the touch and why it can be gently reground and re-polished decades later rather than being thrown away.

Fig. 1 — The tile is cast upside down against glass glass plate (removed later) coloured pattern layer 3–5 fine cement + sand 6–10 coarse backing 12–18 tile face 200 × 200 typical The glass is at the bottom. The pattern is poured first, so it becomes the top face. Because the colour layer is 3–5 mm thick and cast into the body, the pattern wears with the tile instead of rubbing off the top. A worn Athangudi floor can be reground and re-polished; a surface-printed tile cannot.
Fig. 1 — How an Athangudi tile is built up, face-down on glass (section, mm)

How the tile is made

The process is simple to describe and hard to do well. A clean sheet of glass is placed inside a shallow metal frame the size of the tile. A thin metal stencil — a die shaped to the chosen pattern — is laid on the glass. Coloured cement slurry, made of white or grey cement mixed with mineral oxide pigments and a little fine sand, is poured carefully into the separate compartments of the stencil, one colour at a time, by hand. The stencil is then lifted away, leaving the coloured pattern sitting on the glass. A layer of dry cement-and-sand mix is sprinkled over it to absorb moisture, then a thicker backing of coarser cement concrete is added and tamped down. The frame is removed and the tile, still on its glass, is set aside.

After a short initial set, the tile is slid off the glass and cured in water for several days so the cement gains strength, then dried slowly in shade. The whole sequence is manual, which is why each tile carries tiny variations and why the village scale of production survives. It is also why quality varies so much between makers: the ratio of pigment to cement, the cleanliness of the glass, the curing time and the care of the pourer all show up in the finished tile. A well-made tile rings slightly when tapped, has crisp pattern edges and an even sheen; a poor one is dull, chalky and quick to craze.

Fig. 2 — From glass plate to cured tile 1 · Glass + stencil die on clean glass 2 · Pour colours oxide + cement slurry 3 · Backing dry mix + concrete 4 · Cure in water days, then shade-dry Every step is done by hand, so each tile varies slightly. No kiln is used; strength comes from water curing, not from firing. A fresh tile keeps gaining strength for weeks, which is why newly laid floors should not be scrubbed or sealed too early.
Fig. 2 — The four making steps, left to right

Sizes, thicknesses and patterns

Athangudi tiles are most commonly made at 200 × 200 mm (about 8 × 8 inches), with 150 × 150 mm and 250 × 250 mm also available, and borders and special shapes made to order. The thickness is typically 18 to 25 mm — much thicker than a vitrified tile — which is part of why they feel solid and stay cool, and why the floor bed must be planned to take the extra height. Patterns fall into a few families: geometric grids, floral and vine motifs, plain colour fields used as borders, and the characteristic four-tile patterns where the design completes only when four tiles meet. The last of these is the one most often laid wrongly, because the setter does not realise the motif spans four tiles.

AttributeTypical valueNote for specifying
Face size200 × 200 mm (also 150, 250)Confirm actual size; handmade tiles vary ±1–2 mm
Thickness18–25 mmPlan the floor bed for the extra height vs vitrified
Pattern depth3–5 mm coloured layerDeep enough to regrind and re-polish later
Water absorptionHigher than vitrified; needs sealingSeal after laying and curing; reseal periodically
Pattern familiesGeometric, floral, plain, four-tileFour-tile motifs must be set out as a group
VariationSlight colour and sheen variationDry-lay and mix from several boxes before fixing

Where to use them — and where not

Athangudi tiles are at their best on indoor floors that are swept and mopped rather than scrubbed: living rooms, bedrooms, dining areas, foyers, verandahs under cover, and feature walls. They are a superb floor for a home that wants warmth and character, and they handle normal domestic traffic for decades. They are less suited to places that are constantly wet or harshly scrubbed — open showers, swimming-pool surrounds, industrial kitchens — and to full outdoor exposure, where rain and UV are hard on any unglazed cement product. They can be used in bathrooms and semi-outdoor areas, but only with good sealing and the understanding that they need gentle care.

Because the tile is a cement product, two installation points decide whether a floor succeeds. First, the bed must be flat and fully bonded: any hollow under a 20 mm cement tile becomes a crack when a heavy object lands on it. Second, the grout line should be kept thin, around 1.5 to 3 mm, and tinted close to the tile, because a wide dark grout line chops the pattern into squares and destroys the flowing effect the tile is prized for. These are exactly the points machine-tile setters get wrong when they treat an Athangudi tile like a vitrified one.

Fig. 3 — Flat bed, thin grout, and motifs that span four tiles A — Section tile 18–25 bond coat 20–30 screed / RCC joint 1.5–3 B — Four-tile motif (plan) the flower completes only where four tiles meet Lay on a fully bonded, flat bed — any hollow becomes a crack. Keep the joint thin and tinted to the tile, or a wide dark grid will cut the pattern into squares. Always dry-lay four-tile motifs first so the design reads across the whole floor.
Fig. 3 — Laying: bed, thin grout and the four-tile motif (plan + section, mm)

What Athangudi tiles cost

Because the tiles are handmade, prices depend heavily on pattern complexity, number of colours, size and order quantity, and on how far they travel from the Chettinad workshops. The ranges below are indicative for October 2026. Plain and simple geometric tiles sit at the lower end; intricate multi-colour and custom patterns at the upper end. Freight to north and west India adds meaningfully to the delivered cost because the tiles are heavy and a small percentage always break in transit, so a wastage allowance of around 8 to 12 per cent should be ordered.

ItemIndicative rate (Oct 2026)Notes
Plain / simple tile, 200 mm₹35–70 per tileBorders and single-colour fields
Patterned tile, 200 mm₹60–130 per tileGeometric and floral, few colours
Intricate / custom tile₹120–250+ per tileMany colours, bespoke motifs
Supply only, per sq ft₹70–160 per sq ftRoughly 23 tiles of 200 mm per sq metre
Laid, per sq ft₹90–220 per sq ftIncludes bed, laying, thin grout; sealing extra
Sealing / polishing₹25–60 per sq ftAfter curing; repeat every few years

How to tell a good tile from a weak one

  • Tap the tile — a well-cured tile gives a firm, slightly ringing note, while a poorly cured one sounds dull and chalky.
  • Look along the surface in raking light — the sheen should be even, not patchy, and the pattern edges should be crisp, not bleeding.
  • Check the back — the backing should be dense and well compacted, not crumbly or sandy.
  • Wet a sample and let it dry — heavy, lasting dark patches suggest high porosity and a tile that will stain without good sealing.
  • Measure several tiles — a little variation is normal and charming, but wildly inconsistent sizes make for ugly, uneven joints.
  • Ask how long the tiles have cured — tiles that are too fresh are weak, so insist on properly cured stock.
  • Dry-lay a square metre, including any four-tile motif, before approving the batch and before fixing begins.

Patterns and how they are set out

The pattern vocabulary of the Athangudi tile is deep, because the stencil can be shaped into almost anything, and over generations the makers built up a repertoire that ranges from tight geometric grids to flowing floral fields. Understanding the families helps a buyer plan a floor rather than merely picking a nice sample. Geometric grids — squares, stars, interlocking diamonds — are the most forgiving, because they repeat cleanly in any direction and hide small laying errors. Floral and vine patterns are softer and more decorative, and read best where they are seen closely, as in a living room or a feature wall. Plain single-colour tiles are the unsung heroes: used as a border or a field, they frame and calm the patterned tiles, which is how the historic floors avoided looking busy.

The pattern that most often goes wrong is the four-tile motif, in which the design is only a quarter of a flower or medallion on each tile and completes when four tiles meet corner to corner. Laid without planning, the motif scatters into meaningless fragments; laid correctly, with the floor set out from a centre line, it blooms into a repeating rosette that gives the room a woven, rangoli-like richness. The practical rule is to dry-lay the whole motif, and ideally a few repeats of it, before any tile is fixed, and to set the floor out from the centre of the room so that cut tiles fall evenly at the edges rather than leaving a thin, awkward sliver against one wall.

Fig. 4 — Single tiles, four-tile motifs and borders 200 single tile four-tile motif border strip completes across 4 tiles Set the floor out from the centre of the room so cut tiles fall evenly at the edges, and dry-lay any four-tile motif first. A plain border frames a patterned field and keeps the floor from looking busy — the historic floors almost always used one.
Fig. 4 — Single tiles, four-tile motifs and borders set out
Pattern familyLookWhere it suits
Geometric gridRepeating squares, stars, diamondsLarge floors, foyers, halls
Floral / vineCurving flowers and leavesLiving rooms, feature panels
Four-tile motifDesign completes across four tilesCentre of a room, rangoli effect
Plain / solidSingle flat colour fieldFraming a patterned floor
Border stripNarrow repeating edgeSkirting line, defining a field

Caring for an Athangudi floor

Because an Athangudi tile is a cement product, its care is closer to that of a polished concrete or terrazzo floor than to a glazed ceramic one. For the first few weeks after laying, the floor is still gaining strength and should be treated gently — swept and lightly mopped, not scrubbed, flooded or sealed too early. Once cured, routine care is simple: sweep daily, mop with clean water and a mild soap, and wipe spills promptly. The two enemies are acids and abrasion. Acidic cleaners, including strong bathroom and toilet cleaners and some stain removers, etch the cement surface and dull it; harsh scrubbing and gritty pads scratch the sheen. Kept away from both, the floor keeps its soft glow for years.

Sealing is the other half of care. A penetrating sealer suited to cement tiles is applied after the floor has cured, and renewed every few years, to slow water absorption and resist staining; most installers avoid glossy film-forming coatings because they alter the natural sheen and can peel. The great long-term advantage of the tile is that it is renewable. If, after many years, the floor looks tired, it can be lightly reground and re-polished to bring back the surface, and a single cracked tile can be cut out and replaced from the spares that were ordered at the start. This is the opposite of a discontinued ceramic range, where one broken tile can mean an obvious patch forever. The table below sets out a simple maintenance rhythm.

TaskHow oftenNote
Sweep and mopDaily / as neededMild soap and clean water, no acids
ResealEvery 2–4 yearsPenetrating cement-tile sealer
Replace a cracked tileAs neededCut out and set a matching spare
Regrind and re-polishOnce in many yearsRestores the sheen of a tired floor
AvoidAlwaysAcids, abrasive pads, standing water

Set against machine-made floors, the Athangudi tile asks for a little more care and gives back a great deal of character. A vitrified tile is harder, denser and essentially maintenance-free, and it is the right choice for a wet or heavily scrubbed area; but it is also uniform and printed, and when a line is discontinued it cannot be matched. The Athangudi tile trades a little toughness for warmth, repairability and the quiet irregularity of the handmade. For a home that wants a floor with a story and is willing to sweep and seal it, that is a trade well worth making — and it is why designers keep specifying these tiles far from the village where they are still, tile by tile, poured on glass.

Frequently asked questions about Athangudi tiles

Are Athangudi tiles the same as vitrified or ceramic tiles?

No. Vitrified and ceramic tiles are fired in a kiln at high temperature and are dense and low-absorption; Athangudi tiles are cement tiles, cured in water and never fired, with the pattern cast a few millimetres into the surface. That makes Athangudi tiles cooler underfoot, repairable and handmade in character, but also more porous, so they must be sealed and cared for gently.

Do Athangudi tiles need sealing?

Yes. Because they are cement-based and more porous than vitrified tiles, they should be sealed after laying and curing, and resealed every few years, to resist stains and water marks. A penetrating sealer suited to cement tiles is used; glossy film-forming coatings are usually avoided because they change the natural sheen and can peel.

Can Athangudi tiles be used in bathrooms and kitchens?

They can, with care. In bathrooms keep them out of the constantly wet shower zone or seal them well and accept gentle maintenance; in kitchens they work on the floor but should be sealed and wiped rather than scrubbed with harsh acids. For areas that are always wet or heavily scrubbed, a vitrified tile is the safer technical choice.

How long do Athangudi tiles last?

A well-made, well-laid and sealed Athangudi floor lasts for decades — many original floors in Chettinad are a century old and still in use. Because the colour layer is several millimetres deep, a tired floor can be reground and re-polished to look new, and individual cracked tiles can be cut out and replaced, so the floor is genuinely long-lived rather than disposable.

Sources & standards

  1. Bureau of Indian Standards — IS 1237 (cement concrete flooring tiles), the relevant Indian standard for cement tiles
  2. Bureau of Indian Standards — IS 15622 (pressed ceramic tiles) for comparison with fired tiles; IS 4457 (ceramic tiles for chemically resistant units) where relevant
  3. UNESCO World Heritage Centre — Chettinad, Village Clusters of the Tamil Merchants (India's Tentative List): context of the craft region
  4. National Building Code of India 2016, Part 6 (Structural Design) and Part 5 (Building Materials) — flooring beds and material guidance
  5. Neufert, Architects' Data — floor finishes, screeds and laying tolerances
  6. Time-Saver Standards for Architectural Design — floor tile beds and joint practice
  7. Price ranges: indicative October 2026 estimates — confirm locally before budgeting
Discuss your project