Buying an air conditioner in India usually begins and ends with one number: the tonnage. The shop asks how big the room is, suggests a one-ton or a one-and-a-half-ton unit, and the sale is done. Most of the time the rough answer is close enough, but the two failure modes are real and expensive. An undersized unit runs flat out all day, never quite cooling the room, driving up the bill and wearing itself out. An oversized unit cools the air too fast, switches off before it has removed the humidity, and leaves the room cold but clammy, cycling on and off in a way that is both uncomfortable and inefficient. Right-sizing sits between the two, and it depends on more than floor area alone.
The word tonnage is a historical oddity worth clearing up, because it confuses many buyers. It has nothing to do with the weight of the machine. One ton of refrigeration is the cooling power once needed to melt one ton of ice in a day — an old unit of cooling capacity that stuck. A one-ton air conditioner removes heat at that rate; a one-and-a-half-ton unit does half as much again. So tonnage is a measure of cooling power, and matching it to a room means matching the machine's cooling power to the rate at which the room gains heat — from the sun, the walls, the roof, the people, the lights and the appliances inside it.
This article gives the simple tonnage rule of thumb that gets most Indian rooms right, then shows the factors that correctly push the answer up or down, and finally explains the star rating and its ISEER number, which decide not what the unit costs to buy but what it costs to run for the next decade. The rule of thumb is deliberately described as indicative; a hot top-floor room facing west needs an honest heat-load estimate, not a thumb. The prices are indicative October 2026 ranges and should be confirmed locally before buying.
The tonnage rule of thumb
For a quick, reliable starting point, Indian practice uses roughly 0.006 ton of cooling per square foot of floor area for an ordinary room with a normal ceiling height of about 3 metres. That single figure turns a room size into a tonnage: a 100 square foot room wants about 0.6 ton, so a 1 ton unit comfortably covers it; a 150 square foot room wants about 0.9 ton, so a 1 ton unit is about right and a 1.5 ton gives margin; a 200 square foot room wants about 1.2 ton, so a 1.5 ton unit suits it; and a 250 to 300 square foot room wants a 2 ton unit. Because air conditioners are sold in fixed steps — 0.8, 1, 1.5, 2 ton — the rule usually points to the nearest available size, and the margin decides whether to round up.
This rule of thumb is a sound default for a standard room, but it must be treated as exactly that — a rule of thumb, not a calculation. It assumes an average room: normal ceiling height, a wall or two exposed to sun, a window of ordinary size, two or three people, a normal ceiling. The moment a room departs from average — a top-floor room under a hot roof, a west-facing room with a large glass window, a kitchen full of cooking heat, a living room that holds eight people at a party — the heat gain rises and the tonnage with it. The honest method is to start from the rule of thumb and then adjust for the factors the thumb ignores, rounding up to the next standard size whenever several of them point the same way.
| Room area | Rule-of-thumb need | Usual unit |
|---|---|---|
| Up to 110 sq ft | ≈ 0.6 – 0.7 ton | 0.8 – 1 ton |
| 110 – 160 sq ft | ≈ 0.7 – 1.0 ton | 1 – 1.5 ton |
| 160 – 220 sq ft | ≈ 1.0 – 1.3 ton | 1.5 ton |
| 220 – 320 sq ft | ≈ 1.3 – 1.9 ton | 2 ton |
| Above 320 sq ft | ≈ 2 ton or more | 2 ton or two units |
The factors that change the answer
A room is not just a floor; it is a box that gains heat through every surface and from everything inside it, and the tonnage must cover the total. The sun is the biggest variable: a west- or south-facing room takes the brunt of the afternoon sun, and a large glass window lets that heat pour in, so a sunny, glassy room needs noticeably more cooling than a shaded one of the same size. The top floor is the next: a room directly under an exposed terrace bakes under the roof all afternoon and needs more tonnage than the same room on a middle floor. Internal heat matters too — a kitchen's stove and oven, a crowd of people, a bank of lights and electronics all add heat that the air conditioner must remove. Ceiling height counts because a taller room is a larger volume of air to cool.
The practical way to use these factors is to start from the rule-of-thumb tonnage and nudge it up when several apply. A north-facing, shaded, middle-floor bedroom for two can sit at or even below the rule; a west-facing, top-floor living room with a large window that hosts gatherings should round firmly up to the next size. The table below gives sensible adjustments. The aim is not a laboratory calculation but an honest reckoning: a unit that is a little generous for a genuinely hot room will still cool it and dehumidify it properly, whereas a unit sized by floor area alone for a hot room will struggle every afternoon. For difficult rooms a proper heat-load estimate, which a good supplier or engineer can do, is worth the trouble.
| Factor | Effect on tonnage | Why |
|---|---|---|
| West / south sun, big window | Add 0.3 – 0.5 ton | Strong afternoon solar gain through glass |
| Top floor under an exposed roof | Add 0.3 – 0.5 ton | Roof heats the room all afternoon |
| Kitchen or cooking heat | Add 0.3 – 0.5 ton | Stove and oven add heat to the room |
| More than 2 – 3 people regularly | Add 0.1 ton per extra person | Each person adds body heat |
| High ceiling (above ~3.3 m) | Add 0.2 – 0.3 ton | Larger air volume to cool |
| Shaded, north-facing, middle floor | No change or slightly less | Low heat gain |
Why an oversized AC is also a mistake
It is tempting to think that if a one-and-a-half-ton unit is enough then a two-ton unit must be better. It is not, and the reason is humidity. An air conditioner does two jobs: it cools the air and it dries it, and the drying happens only while the unit runs. An oversized unit cools the room so quickly that it reaches the set temperature and switches off before it has pulled much moisture out of the air. The room ends up cold but damp — a clammy, uncomfortable chill — and the unit short-cycles, turning on and off repeatedly, which wastes energy and wears the compressor. An under-loaded unit also costs more to buy for no benefit. Right-sizing, or at most a modest margin, keeps the unit running long enough to dehumidify properly and comfortably.
The inverter air conditioner softens this trap, and it is now the sensible default. A fixed-speed unit runs at full power or not at all, so sizing is less forgiving; an inverter unit varies its compressor speed, running gently and continuously to hold the temperature, which both dehumidifies better and saves energy. An inverter unit tolerates a small oversize more gracefully than a fixed-speed one, but it is not a licence to buy far too much machine. The goal remains to match tonnage to the room's real heat load, choose an inverter unit, and let it run steadily. Buying deliberately oversized to cool a room faster is a false economy that trades comfort and efficiency for a few quicker minutes at start-up.
Star rating and ISEER: what it costs to run
Tonnage decides whether an air conditioner can cool the room; the star rating decides what it costs to do so, and over a decade of hot Indian summers the running cost dwarfs the purchase price. The Bureau of Energy Efficiency runs the star-rating scheme, from one star to five, printed on the familiar label on every unit. The more stars, the less electricity the unit uses for the same cooling. Behind the stars sits a number called ISEER — the Indian Seasonal Energy Efficiency Ratio — which measures cooling delivered per unit of electricity across a representative Indian cooling season; a higher ISEER means a more efficient unit. A five-star inverter unit can use substantially less power than a one- or two-star unit of the same tonnage, and the saving on the electricity bill repays the higher purchase price, often within a few seasons for a unit that runs a lot.
The sensible buying logic follows from this. Size the tonnage correctly for the room first; then, within that tonnage, buy the highest star rating the budget allows, especially for a unit that will run many hours a day through a long summer, because that is where the efficiency pays back. A bedroom air conditioner that runs every night and a living-room unit that runs all evening both justify a four- or five-star inverter machine. A unit in a guest room used a few weeks a year matters less. The star label is not marketing; it is the single best predictor of the electricity bill, and reading it is the second decision after tonnage, not an afterthought.
| Star rating | Relative efficiency (ISEER) | Running cost | Best for |
|---|---|---|---|
| 1 – 2 star | Lowest | Highest bill | Light, occasional use only |
| 3 star | Moderate | Moderate bill | Rooms used a few hours a day |
| 4 star | High | Low bill | Bedrooms and living rooms used daily |
| 5 star (inverter) | Highest | Lowest bill | Heavy daily use through long summers |
Split or window, and what it costs
Two broad types are sold. The window air conditioner is a single box set into a wall or window opening, cheaper to buy and install and simpler to service, but noisier inside the room and dependent on a suitable opening. The split air conditioner separates the quiet indoor unit from the noisy outdoor compressor, cools more quietly, looks neater and suits most modern rooms, at a somewhat higher price and with a proper installation of pipe and wiring between the two units. For most homes today the split is the default; the window unit survives where cost rules or a split cannot easily be installed. Whichever is chosen, the indoor unit of a split is mounted high on the wall at about 2100 to 2400 millimetres with clear airflow, and the outdoor unit is given shade, ventilation and at least 300 millimetres of clearance on each side with as short a pipe run as possible.
Prices below are indicative October 2026 ranges for the unit, before installation, which typically adds a few thousand rupees for a split. They rise with tonnage and, importantly, with star rating — a five-star inverter unit costs more than a three-star unit of the same tonnage, and that premium is the down payment on a lower electricity bill. The right way to read the table is to settle the tonnage from the room first, then move up the star ratings within that tonnage as far as the budget and the hours of use justify. For a unit that will run every day through a Surat or a Delhi summer, the higher star rating is almost always the cheaper choice over its life, even though it costs more on the day of purchase.
| Unit | Indicative price (unit only) | Note |
|---|---|---|
| 1 ton split | ₹28,000 – ₹42,000 | Small bedroom; add install |
| 1.5 ton split | ₹36,000 – ₹58,000 | The most common home size |
| 2 ton split | ₹52,000 – ₹78,000 | Large or sunny rooms |
| 1.5 ton window | ₹30,000 – ₹42,000 | Cheaper, noisier, needs an opening |
| 5-star inverter premium | +₹5,000 – ₹15,000 | Over a 3-star unit of same tonnage |
| Split installation | ₹1,500 – ₹3,500 | Pipe, wiring, bracket, labour |
Where room cooling is heading
Air conditioning in India is moving in two directions at once: towards greater efficiency and towards less reliance on the machine. On the efficiency side, inverter technology, higher ISEER ratings and smarter controls keep cutting the energy needed per degree of cooling, and the star-rating thresholds are periodically tightened so that today's five-star unit becomes tomorrow's ordinary one. On the other side, the recognition that air conditioning is costly and energy-hungry is pushing designers back towards reducing the heat load before sizing the machine — shading west windows, insulating a hot roof, using lighter wall finishes, cross-ventilating at night — so that a smaller, cheaper unit does the job. The residential energy code and green building practice both reward this approach. The direction is clear: cool the room, but first design it so that less cooling is needed, and then size an efficient unit honestly to the load that remains.
Rules for sizing and buying an AC
- Start from the rule of thumb — about 0.006 ton per square foot — to get a baseline tonnage.
- Round up a size when a room faces west sun, sits under an exposed roof, holds a kitchen or hosts crowds.
- Do not oversize deliberately: too large a unit leaves the room cold but humid and short-cycles.
- Prefer an inverter unit; it dehumidifies better, saves energy and tolerates a small margin gracefully.
- Settle the tonnage first, then buy the highest star rating the budget and the hours of use justify.
- For a difficult, hot room, get a proper heat-load estimate rather than relying on floor area alone.
- Mount the split indoor unit high (2100–2400 mm) with clear airflow and nothing blocking the throw.
- Give the outdoor unit shade, ventilation, at least 300 mm clearance each side and a short pipe run.
- Reduce the heat load first — shade glass, insulate the roof — so a smaller, cheaper unit suffices.
Frequently asked questions
What size AC do I need for a 150 sq ft room?
About 0.9 ton by the rule of thumb, so a 1 ton unit suits a shaded, average room and a 1.5 ton gives margin. If the room faces west, sits on the top floor or holds several people, choose the 1.5 ton. Settle the tonnage first, then pick a high star rating within it.
How many square feet does a 1.5 ton AC cover?
Roughly 160 to 250 square feet of ordinary room at a normal ceiling height, by the 0.006 ton per square foot rule. A hot, sunny or top-floor room of that size may need the next step up to 2 ton, while a shaded, well-insulated room may be comfortable at the larger end of the range.
Is a higher tonnage AC always better?
No. An oversized unit cools the air before it has removed the humidity, leaving the room cold but clammy, and it short-cycles, wasting energy and wearing the compressor. Match the tonnage to the room's real heat load, with at most a modest margin, rather than buying far more cooling power than the room needs.
What is ISEER and does it matter?
ISEER, the Indian Seasonal Energy Efficiency Ratio, measures how much cooling a unit delivers per unit of electricity across a representative Indian season; it underlies the star rating. It matters a great deal, because over a decade of use the electricity bill far exceeds the purchase price, and a higher-ISEER, higher-star unit costs much less to run.
Should I buy a window or split AC?
A split is quieter, neater and the usual choice for modern rooms, at a higher price and with a proper installation between the indoor and outdoor units. A window unit is cheaper and simpler but noisier and needs a suitable opening. For most homes the split is the default; the window unit suits tight budgets or where a split cannot be installed.
Sources & standards
- Bureau of Indian Standards — National Building Code of India 2016, Part 8 (Building Services), Section 3: Air Conditioning, Heating and Mechanical Ventilation
- Bureau of Energy Efficiency — Standards and Labelling (star rating) programme for room air conditioners and the ISEER metric
- Bureau of Energy Efficiency — Energy Conservation Building Code (ECBC) and Eco-Niwas Samhita for residential buildings
- Indian Society of Heating, Refrigerating and Air Conditioning Engineers (ISHRAE) — handbook guidance on cooling load and system sizing
- Ernst and Peter Neufert — Architects' Data: thermal comfort and air conditioning
- Joseph De Chiara, Julius Panero and Martin Zelnik — Time-Saver Standards for Interior Design and Space Planning: mechanical services and comfort
- Price ranges: indicative October 2026 estimates — confirm locally before budgeting



