Most Indian homes get their CCTV the wrong way round. A system is bought as an afterthought — four cameras, a recorder and a coil of wire — long after the walls are plastered and the false ceiling is closed. The installer then runs cable along skirtings, drills through finished walls, taps power from the nearest point and leaves a recorder balanced on top of a wardrobe. It works for a while, then the wires sag, the hard disk overheats in a cupboard with no air, a camera points at a wall because the only mounting spot was already decided, and nobody can find the recorder when the police ask for footage. None of this is a camera problem. It is a planning problem.
Security wiring belongs in the same conversation as electrical and network wiring, drawn on a plan before the first conduit is laid. The cameras themselves are the cheapest and most replaceable part of the system; the cable routes, the conduit, the power and the recorder location are what make the difference between a system that lasts a decade and one that is ripped out in two years. A home that plans its security backbone early can start with four cameras and grow to twelve on the same cabling, move from an old recorder to a new one without touching a wall, and keep every wire hidden.
This article treats home CCTV as a wiring and infrastructure subject rather than a shopping list. It covers how the technology moved from grainy analogue tape to networked Power-over-Ethernet cameras, how a system is wired in an Indian home today, where cameras should actually be placed and at what height, how the cable and conduit are routed to a single equipment point, what power and backup the system needs, and what a sensible home installation costs. The emphasis throughout is on decisions that are expensive to change later and cheap to get right at the planning stage.
Why security wiring must be planned, not patched
The case for early planning is simple arithmetic. Running a cable inside a wall chase before plaster costs a few hundred rupees and leaves no trace; running the same cable after the house is finished means surface conduit, drilling through finished surfaces, or an ugly route along the skirting, and it costs several times more while looking worse. A camera position decided on a plan can be placed where it sees a door, a gate and a boundary at once; a camera position decided on site is wherever a wire happens to reach. The recorder, the switch and the backup battery need a ventilated, lockable, reachable cupboard — something that has to be designed into the joinery, not discovered afterwards.
Planning also protects the system from the single most common failure in Indian homes: heat. A network video recorder and its hard disk run continuously and generate warmth; sealed inside a wardrobe or a tight niche in a city like Surat or Ahmedabad, where summer interiors cross 35 degrees, the disk's life collapses and recordings are lost exactly when they are needed. A planned equipment cupboard has ventilation, a dedicated power point, an uninterrupted supply and room for the cables to be dressed and labelled. These are not luxuries; they are the difference between a system that has footage and one that does not.
A short history: from analogue tape to Power-over-Ethernet
Home CCTV in India began as a scaled-down version of commercial analogue systems. A camera sent an analogue video signal down a coaxial cable to a recorder, first a tape machine and later a digital video recorder (DVR) with a hard disk. Each camera needed its own coaxial run plus a separate power wire, pictures were low resolution, and viewing meant sitting in front of the recorder. These systems were cheap and are still sold, now in high-definition form over coax (HD-TVI, AHD and CVI), and they remain a reasonable choice for a small, fixed installation.
The larger shift came with the internet-protocol (IP) camera, which turns the picture into network data and sends it down an ordinary Ethernet cable. The important advance for wiring was Power-over-Ethernet (PoE): a single Cat6 cable now carries both the picture and the power, so each camera needs one wire instead of two, and the power comes from a switch in the equipment cupboard rather than an adaptor at every camera. A home wired with Cat6 to each camera position can run almost any modern camera, record to a network video recorder (NVR), and add cameras later on spare cable. This is why, even in a modest home, running structured Cat6 cable to planned camera points is the most future-proof decision available.
Alongside wired systems came the battery and Wi-Fi camera, which needs no cable at all and streams to a phone through the home router and a cloud service. These are genuinely useful for renters and for spots where no cable was run, but they depend on battery changes, Wi-Fi coverage and a subscription, and the picture can stutter when the network is busy. The present-day sensible home uses wired PoE cameras for the fixed, important positions — gate, main door, boundary — and keeps wireless cameras for temporary or hard-to-reach spots. The wiring plan should assume the fixed positions are cabled.
How home CCTV is wired today in India
A modern home system has four parts, and the wiring connects them. The cameras sit at the edges of the property. Each camera's cable runs back, inside conduit, to a central equipment point. At that point sits the recorder — a DVR for coax systems, an NVR with a PoE switch for IP systems — together with a hard disk for storage and an uninterrupted power supply. From there, a single cable to the home router lets the owner view the cameras on a phone. The whole system should sit on one planned backbone so that adding a camera means pulling one more cable to the cupboard, not rebuilding anything.
The choice between coax and Cat6 is the first wiring decision. Coaxial HD systems are cheaper per camera and tolerate very long runs, but need a separate power wire and cannot easily be repurposed. Cat6 with PoE costs a little more but carries power and data in one cable, supports higher resolutions, and can later serve data points, access points or a video door phone. For any new home or major renovation, Aaditya Interior's standard recommendation is structured Cat6 cabling to every camera point, because the incremental cost at the wiring stage is small and the flexibility is large. The table below sets out the camera types a home actually chooses between.
| Camera type | Typical resolution | Best position | Note |
|---|---|---|---|
| Fixed dome (indoor/sheltered) | 2–4 MP | Entrance lobby, staircase, inside gate | Vandal-resistant, discreet, fixed field of view |
| Fixed bullet (outdoor) | 2–5 MP | Boundary wall, driveway, parking | Long throw, visible deterrent, needs good weather sealing |
| Turret / eyeball | 4–5 MP | Porch, terrace, side passage | Less glare from its own infra-red at night than a dome |
| Pan-tilt-zoom (PTZ) | 4–8 MP | Large compound, one commanding position | Can track and zoom; costs far more, one blind moment while moving |
| Video door phone camera | 2 MP | Main door / gate | Combines bell, intercom and camera; wires to an indoor panel |
| Wireless / battery | 2–4 MP | Temporary spots, no-cable corners | Needs Wi-Fi, charging and usually a subscription |
| Wiring choice | Coax HD (TVI/AHD/CVI) | Cat6 with PoE (IP) |
|---|---|---|
| Cables per camera | Two — coax for video, wire for power | One — video and power share the cable |
| Resolution ceiling | Up to about 5 MP today | Higher, and improving faster |
| Run length tolerance | Very long runs tolerated | About 90 m per run from the switch |
| Future flexibility | Hard to repurpose the cable | Same cable serves data, Wi-Fi points, door phone |
| Relative cost per camera | Lower at entry level | A little higher, far more room to grow |
| Best for | Small, fixed, budget installations | New homes and major renovations |
Planning camera positions and coverage
Camera placement is a design task, not a shopping one. The first rule is to cover approaches, not interiors: the gate, the main door, the driveway, the boundary and the parking matter far more than the inside of rooms, both for security and for privacy. The second rule is to make cameras see one another's blind spots, so that an intruder who disables one camera is already in the frame of the next. The third rule is to point cameras with the sun and the gate in mind — a camera staring west into the evening sun, or straight at a bright gate lamp, produces a silhouette and nothing useful.
Mounting height is the detail most often wrong. Too low, and a camera is easily reached and knocked; too high, and it sees the tops of heads and no faces. For a camera meant to identify faces, a mounting height of about 2400 to 2800 mm with a gentle downward tilt of ten to fifteen degrees works well, keeping faces in frame while staying out of easy reach. Overview cameras on a boundary or terrace can go higher, around 3000 to 3600 mm, because their job is to show movement and direction rather than faces. Every camera should be mounted on solid masonry or a proper bracket, never on a thin fascia board that vibrates in the wind and blurs night recordings.
| Position | Camera | Mounting height | Points at |
|---|---|---|---|
| Main gate / driveway | 4 MP bullet | 2400–2800 mm | Vehicles and people entering, number plates at the gate line |
| Main door / porch | 4 MP dome or door phone | 2100–2400 mm | Faces of anyone at the door |
| Boundary corners | 4 MP bullet | 3000–3600 mm | The length of two walls from one corner |
| Rear yard / service | 4 MP bullet | 2700–3000 mm | The blind side of the house and the back gate |
| Parking / stilt | 5 MP turret | 2400–2800 mm | Parked vehicles and the ramp |
| Staircase / lobby (indoor) | 2 MP dome | 2400–2700 mm | Internal circulation, only where privacy allows |
Cabling, conduit and the backbone
With positions fixed, the cable routes are drawn. Each camera point gets a conduit — typically a 25 mm PVC conduit for a single Cat6 cable, or a larger 32 mm conduit where two cables share a route — run inside the wall chase or above the false ceiling, back to the equipment cupboard. The conduit is pulled before plaster with a draw-wire left inside so cables can be replaced without breaking walls. Outdoor runs use UV-stable conduit and are sealed at both ends against water and lizards. The cable itself should be genuine solid-copper Cat6, not copper-clad aluminium, because PoE power loss and heat on undersized conductors is a real and common cause of cameras dropping out.
Cable length matters. A Cat6 PoE run should stay within about 90 metres from the switch to the camera, with a little margin left for patch leads; most home runs are far shorter, but a camera at the far corner of a large plot can approach the limit, and that is a reason to place the equipment cupboard centrally rather than in a far corner. Coaxial HD runs tolerate longer distances but still degrade, so the same discipline of a central equipment point applies. The backbone should also carry one spare conduit from the cupboard to the loft or terrace, because the next camera, access point or sensor always wants a route that was not drawn.
Power, backup and the equipment cupboard
The equipment cupboard is where a planned system shows its worth. It should be a ventilated, lockable space — a dedicated niche in the utility area, a shelf in a services cupboard, or a small wall-mounted rack — with a dedicated power point on its own circuit, not shared with a geyser or a pump that trips it. Inside sit the recorder, the hard disk, the PoE switch, the router or an extension of it, and the backup power. Airflow matters: even a few ventilation slots and a small fan keep the disk cool enough to reach its rated life. Cables are dressed, labelled and left with a little slack so a device can be swapped without re-pulling anything.
Backup power is what keeps a system honest. A small uninterruptible power supply (UPS) sized for the recorder, the switch and the router gives the cameras and recording perhaps fifteen to sixty minutes through a power cut, which covers most Indian outages and, importantly, means the system keeps watching during the very moments a cut might be used as cover. The UPS should run the switch too, because a PoE switch on backup keeps the cameras themselves powered. Storage is sized from the number of cameras, their resolution and how many days of footage are wanted; a common home target is one to two weeks of continuous recording, which a 1 to 2 TB surveillance-grade hard disk usually provides for four to eight cameras.
Door phone, intercom and alarm on the same backbone
CCTV rarely travels alone. A video door phone, a motion sensor at the gate, a sensor on the main door, a siren and sometimes an access-control keypad all belong to the same security idea, and they share the same planning logic: decide positions early, run cable in conduit to the equipment point, and give them backup power. A video door phone in particular wants its cable run before plaster, from the gate or door to an indoor panel, often near the kitchen or living area where someone is usually present. Running these alongside the CCTV conduit, on the same plan, avoids a second round of wall-chasing a year later.
The modern convenience is that much of this can be watched from one phone app, but the wiring underneath should not depend on the internet to function. A good home system records locally to its own disk whether or not the broadband is up, and uses the cloud only for remote viewing and off-site backup of important clips. Designing it this way means a cut line or a dead router degrades convenience, not the core job of recording. The app is the window; the cable and the disk are the house.
What a home system costs
Costs vary with the number of cameras, their resolution, the recorder, the cabling distances and the quality of installation, but indicative October 2026 ranges help set a budget. Individual cameras run from about ₹1,200 to ₹2,500 for a 2 MP unit, ₹2,000 to ₹4,000 for a 4 MP camera, and ₹6,000 to ₹20,000 for a 5 MP turret or a PTZ. A four-channel NVR or DVR costs about ₹3,500 to ₹8,000 and an eight-channel unit about ₹6,000 to ₹14,000, with a 1 to 2 TB surveillance hard disk adding ₹4,000 to ₹8,000. Cat6 cable is about ₹20 to ₹45 per metre and coaxial about ₹18 to ₹30 per metre, with per-point cabling, conduit and termination labour of roughly ₹400 to ₹900 a point.
| Item | Indicative cost (Oct 2026) | Notes |
|---|---|---|
| 2 MP camera | ₹1,200 – ₹2,500 | Entry-level, for sheltered indoor spots |
| 4 MP camera | ₹2,000 – ₹4,000 | The sensible default outdoors |
| 5 MP turret / PTZ | ₹6,000 – ₹20,000 | PTZ at the top of the band |
| 4-channel NVR/DVR | ₹3,500 – ₹8,000 | 8-channel ₹6,000 – ₹14,000 |
| 1–2 TB surveillance disk | ₹4,000 – ₹8,000 | Surveillance-grade, not a desktop disk |
| 8-port PoE switch | ₹3,500 – ₹9,000 | Only for IP/PoE systems |
| Cat6 cable (per metre) | ₹20 – ₹45 | Solid copper; coax RG59 ₹18 – ₹30/m |
| Per-point cabling + conduit | ₹400 – ₹900 | Labour and material per camera point |
| Video door phone | ₹6,000 – ₹18,000 | Camera, bell and indoor panel together |
| UPS / battery backup | ₹3,000 – ₹9,000 | Sized for recorder, switch and router |
Put together, a tidy four-camera PoE home system with an NVR, a disk, a switch, cabling and a UPS commonly lands around ₹18,000 to ₹45,000 installed, and an eight-camera system around ₹40,000 to ₹90,000, depending on camera resolution and cable lengths. A coaxial HD system can be cheaper at the low end but offers less room to grow. These are material-plus-labour figures excluding GST and should be confirmed with a local installer, because cable runs and mounting difficulty swing the labour component considerably.
Where home security is going
The direction of travel is clear: cameras are getting smarter at the edge, so that a recorder can distinguish a person from a passing dog or a swaying tree and alert only on the former, cutting the flood of false notifications that makes people ignore their systems. Number-plate recognition at the gate, two-way audio, and integration with lighting and locks are moving from commercial into home use. Storage is splitting between a local disk for the bulk and the cloud for important clips, so footage survives even if the recorder is stolen. None of this changes the wiring brief: a smart camera still wants a reliable cable, steady power and a cool, lockable home for its recorder.
For anyone building or renovating now, the future-proof move is modest and cheap — run structured Cat6 in conduit to every sensible camera point, plan a ventilated equipment cupboard with its own circuit and a small UPS, and leave one spare conduit to the terrace. Whatever camera and recorder technology arrives next will almost certainly run on that backbone. The hardware will be replaced two or three times over the life of the house; the cabling and the cupboard, if planned well, will not need to be.
Ten rules for planning home security wiring
- Plan camera positions and cable routes on the drawings before plaster, with the electrical and network wiring.
- Cover approaches — gate, door, driveway, boundary — not the insides of private rooms.
- Make each camera see the next camera's blind spot, so disabling one still leaves an intruder in frame.
- Mount face-identifying cameras at 2400–2800 mm with a 10–15° downward tilt; overview cameras higher.
- Run genuine solid-copper Cat6 in 25 mm conduit to every point, with a draw-wire left inside.
- Keep each PoE run under about 90 m, and place the equipment cupboard centrally to shorten runs.
- Give the recorder a ventilated, lockable cupboard on its own power circuit — never a sealed wardrobe.
- Fit a UPS sized for recorder, switch and router so recording continues through a power cut.
- Record locally to a surveillance-grade disk; use the cloud only for remote viewing and clip backup.
- Label every cable at both ends and leave one spare conduit to the terrace for the next device.
Frequently asked questions
Is a wired CCTV system better than a wireless one for a home?
For the fixed, important positions — gate, main door, boundary — a wired PoE system is more reliable, because it does not depend on Wi-Fi coverage, battery charge or a subscription, and it records continuously to a local disk. Wireless cameras are genuinely useful for temporary spots or corners where no cable was run, but they are best treated as additions to a wired core rather than the whole system.
How many cameras does a normal house need?
Most independent homes are well covered by four to six cameras: the main gate and driveway, the main door, one or two boundary corners, the rear yard and the parking. Flats usually need far fewer, often just the main door and perhaps a balcony. The right number comes from covering every approach and making cameras overlap, not from a round figure.
Can CCTV be added after the house is finished?
Yes, but it is more expensive and less tidy. Cables then run in surface conduit or along skirtings, camera positions are limited to where wires can reach, and walls may need drilling. This is exactly why the wiring is worth planning before plaster — the conduit and draw-wires cost very little at that stage and leave no trace.
Will the cameras keep recording during a power cut?
Only if the system is on backup power. A small UPS sized for the recorder, the PoE switch and the router keeps the cameras powered and recording through typical outages, which also matters because a power cut can be used as cover. Without backup, the system goes dark exactly when it may be needed most.
How long is footage kept?
It depends on the number of cameras, their resolution and the disk size. A common home target is one to two weeks of continuous recording, which a 1 to 2 TB surveillance-grade hard disk usually provides for four to eight cameras; motion-only recording stretches this further. Important clips can also be backed up to the cloud so they survive even if the recorder is removed.
Sources & standards
- Bureau of Indian Standards — IS 694 (PVC insulated cables) and IS 732 (code of practice for electrical wiring installations)
- National Building Code of India 2016, Part 8 — Building Services (electrical and allied installations)
- Telecommunications industry structured-cabling practice — Category 6 balanced cabling, 90 m horizontal channel limit (generic standard range)
- IEEE 802.3af/at — Power-over-Ethernet, as implemented by camera and switch manufacturers (generic standard description)
- Bureau of Energy Efficiency and manufacturer datasheets — typical power draw of NVRs, switches and surveillance hard disks (generic ranges)
- Price ranges: indicative October 2026 estimates — confirm locally before budgeting



