The kitchen chimney is the one appliance in an Indian home that is almost always fixed at the wrong height, and almost nobody notices until the kitchen stays smoky. Indian cooking is not gentle on air. A single tadka of mustard and curry leaves, a tawa full of rotis, a kadhai of deep-frying or a pressure cooker letting off steam throws up a dense, oily, spice-laden plume that a European extractor hood was never designed for. The chimney has to catch that plume at the moment it leaves the pan — and whether it does depends, more than on its suction rating, on how far it sits above the flame.
The common mistakes are predictable. The modular kitchen is designed first, the overhead cabinets are set at a tidy line, and the chimney is then slotted into whatever vertical gap is left, often 900 mm or more above the hob so that it aligns with the wall units. At that height even a powerful chimney pulls in mostly room air and lets the smoke drift sideways to the ceiling. The opposite mistake is just as common in small kitchens: the chimney is dropped low to look dramatic, 550 mm or less above a gas flame, where the heat bakes the baffle filters, discolours the metal and forces the tall cook to duck. Neither kitchen works, and neither is the chimney's fault.
This article fixes the number first and then explains it. The working standard that chimney manufacturers, modular-kitchen fabricators and studios such as Aaditya Interior use across India is a clearance of about 650 to 750 mm — roughly 26 to 30 inches — from the hob surface to the underside of the chimney. From there it sets out how the height changes for gas versus induction, for wall-mounted versus island versus built-in chimneys, how the duct and the height work together, and the fixing details that keep a heavy chimney safely on the wall for a decade.
The number first: 650 to 750 mm above the hob
The single figure worth remembering is the gap between the top of the hob and the bottom of the chimney: about 650 to 750 mm for a gas hob, and about 550 to 650 mm for an induction or electric cooktop. Most Indian chimney brands print a recommended range in their manuals that falls inside this band, and the midpoint — around 700 mm for gas — is a safe default for a standard kitchen with a 850 to 900 mm counter and a reasonably tall cook. The distance is measured vertically from the hob surface to the lowest metal of the chimney canopy, not to the filters recessed inside it.
Why this band and not higher? A rising plume of hot cooking fumes behaves like an expanding cone. Close to the pan it is narrow, fast and hot, and a hood placed within about 700 mm captures almost all of it. As the plume rises it slows, cools, widens and begins to mix with room air; by a metre above the flame it has spread wider than most hoods and lost the upward push that carries it into the throat of the chimney. Raising a chimney from 700 mm to 900 mm does not just make it slightly less effective — it moves the hood out of the fast, narrow part of the plume into the slow, wide part, so a large share of the smoke simply escapes sideways before it is caught.
| Cooktop type | Recommended clearance to canopy | In inches | Why it differs |
|---|---|---|---|
| Gas hob (3–4 burner) | 650–750 mm | ≈ 26–30 in | Tall, hot flame plume; needs room below so filters do not scorch |
| Gas hob (5-burner, high BTU) | 700–750 mm | ≈ 28–30 in | Bigger flames throw heat higher; keep to the upper band |
| Induction / electric cooktop | 550–650 mm | ≈ 22–26 in | No flame, cooler rising air; the hood can sit a little lower |
| Built-in hob with tall cook | 700–800 mm | ≈ 28–32 in | Add height for head clearance; verify the model's maximum |
Why height beats suction rating
Buyers choose chimneys by their airflow number — the suction in cubic metres per hour — because that is what the showroom advertises. Airflow matters, but it is the second question. A 1200 m³/hr chimney mounted at 950 mm performs worse in practice than a 1000 m³/hr chimney mounted at 700 mm, because suction falls off sharply with distance while the plume widens. The chimney can only pull in the air directly beneath its hood; smoke that has already drifted outside that footprint is gone. Correct height keeps the smoke inside the footprint long enough to be caught; raw suction only helps once it is there.
Height also decides how much the chimney has to fight the kitchen's own air currents. An open window, a ceiling fan on low, or the draught from a door swing can all push a rising plume sideways. The lower the hood sits within the sensible band, the shorter the distance the smoke travels before capture, and the less chance a cross-draught has to deflect it. This is why studios turn the ceiling fan off while cooking and advise against placing the hob directly under or beside a strong window draught — both undo the work the chimney height is doing.
Hood size and the height work together
A wider hood catches a wider plume, which is why the hood should at least cover the full spread of the burners and ideally overhang them slightly. A 600 mm hood over a four-burner gas hob is the common minimum in Indian kitchens; a 900 mm hood is better and almost essential over a five-burner hob or a cooktop used for heavy frying. The relationship is simple: a larger hood tolerates a slightly greater height because it still covers the widened plume, while a narrow hood must be kept lower to stay within the narrow part of the cone. Never pair a small hood with a tall mounting — that combination catches the least smoke of all.
A short history: from the window to the chimney
Indian kitchens managed cooking smoke for generations without a chimney at all. The traditional answer was the opening — a high window, a roshandan or ventilator near the ceiling, and often a gap left between the wall and the roof — through which hot smoke rose and escaped by its own buoyancy. Wood and coal chulhas produced far more smoke than a modern gas flame, and the architecture responded with tall ceilings and cross-ventilation that pulled the smoke up and out. The kitchen was frequently placed at the rear or in a separate block so that smoke and heat stayed away from living spaces.
The wall-mounted electric exhaust fan arrived next and became the standard mid-century solution: a propeller fan set high in the kitchen wall, throwing smoke straight outside. It is cheap and effective at clearing a room, but it does nothing at the pan — the smoke still rises past the cook's face before the fan removes it from the room, and the grease settles on every surface on the way. The ducted kitchen chimney, which captures fumes at source directly above the hob, became common in Indian urban homes only from the early 2000s as modular kitchens spread. It is now treated as standard equipment, but the knowledge of how to position it has lagged behind its popularity, which is exactly why the height is so often wrong.
Height by chimney type
The 650–750 mm band is written for the most common case, the wall-mounted chimney over a hob against a wall. Other configurations shift the thinking. An island chimney, hung from the ceiling over a hob in a kitchen island, is more exposed to cross-draughts on all four sides, so it is kept towards the lower end of the band — about 650 to 700 mm over gas — and usually needs a larger hood and higher airflow to compensate. A built-in or under-cabinet chimney concealed inside a hood cabinet follows the same clearance to its working face, with the cabinet designed around it rather than the other way round. A downdraft extractor, which rises from behind the hob, bypasses the height question entirely but is rare and far costlier in Indian kitchens.
| Chimney type | Typical hood width | Mounting height (gas) | Best suited to |
|---|---|---|---|
| Wall-mounted (hob on wall) | 600 or 900 mm | 650–750 mm | Most Indian kitchens; straight or L-shaped layouts |
| Island (hob in island) | 900 mm | 650–700 mm | Open kitchens with a cooking island; needs ceiling duct |
| Built-in / under-cabinet | 600 or 900 mm | 650–750 mm to face | Minimal look; concealed inside a hood cabinet |
| Downdraft (rises behind hob) | Hob-width slot | Not applicable | Rare, premium; island hobs where no overhead hood is wanted |
Height, duct and the air the chimney must move
The height decision cannot be made without the duct. A ducted chimney only works if the air it pulls in can leave the building, and the duct is where most installed chimneys quietly lose their performance. Every bend, every metre of flexible pipe and every undersized section adds resistance that the motor must overcome, so a chimney forced through a long, twisting duct behaves as though it were mounted higher than it is — the effective suction at the hood drops. A clean, short, straight duct of the correct diameter lets the chimney perform at its rated airflow and makes the correct height genuinely effective.
The practical rules Indian installers follow are straightforward. Keep the duct as short and straight as possible, ideally under about 3 metres of total run. Use rigid pipe rather than corrugated flexible hose where it can be seen through, because corrugations add drag. Limit the number of 90-degree bends to two at most; each sharp bend costs airflow equivalent to roughly a metre of straight pipe. Keep the duct diameter at the manufacturer's size — commonly 150 mm — and never pinch it down to fit a smaller wall sleeve. And terminate it outside with a cowl that keeps rain and birds out without choking the opening.
| Duct factor | Good practice | What goes wrong otherwise |
|---|---|---|
| Total duct run | Under 3 m where possible | Long runs bleed suction; smoke lingers at the hood |
| 90-degree bends | Two at most | Each sharp bend costs roughly 1 m of straight pipe |
| Pipe type (visible runs) | Rigid round pipe | Corrugated flexible hose adds drag along its whole length |
| Diameter | Keep the maker's size (often 150 mm) | Pinching to a smaller sleeve throttles the airflow |
| Outlet | Cowl that excludes rain and birds | An open hole lets water and nesting in; a fine mesh chokes it |
Fixing a heavy chimney safely
A kitchen chimney with a glass or steel canopy and a motor is a heavy appliance hung over the cook's head, so the fixing is a safety matter, not a finishing detail. The bracket must be anchored into a solid wall — brick or RCC — with proper wall plugs and screws, never into a hollow partition, a gypsum board or loose plaster alone. Where the wall behind is weak, a backing plate or a frame fixed to the slab carries the load. The chimney's own weight, plus the vibration of the motor and the pull of the duct, work the fixings loose over years, so the anchor has to be generous from the start.
Two clearances matter alongside the height. First, the chimney and its ducting should keep a sensible distance from the gas cylinder and its pipe; the cylinder belongs in a ventilated low cabinet, not sealed in an airtight box under the hob, and the chimney must never be used as an excuse to enclose it. Second, the electrical point for the chimney should sit to the side, not directly above the hob where heat and grease reach it, and it must be on an earthed socket. These are the details a careful installer and a studio such as Aaditya Interior check before the chimney goes up, because they are awkward and costly to correct afterwards.
Chimney cost and what the height has to do with it
Height costs nothing to get right — it is set by a tape measure during installation — yet getting it wrong wastes the money spent on the chimney itself. Indicative October 2026 prices for a 60 cm auto-clean wall-mounted chimney run about ₹12,000 to ₹18,000, with 90 cm models and higher-suction units climbing to ₹30,000 and beyond; island chimneys typically sit around ₹30,000 to ₹55,000 because of their larger hood and ceiling duct. Installation, ducting and the outlet cowl are usually extra. The point for a homeowner is blunt: a correctly mounted ₹15,000 chimney outperforms a carelessly mounted ₹40,000 one, so the height and the duct deserve as much attention as the price tag.
| Chimney / item | Indicative Oct 2026 cost | Note |
|---|---|---|
| 60 cm auto-clean, wall-mounted | ₹12,000–18,000 | The common Indian kitchen default; verify locally |
| 90 cm high-suction, wall-mounted | ₹20,000–40,000 | Preferred over a 4–5 burner hob; verify locally |
| Island chimney, 90 cm | ₹30,000–55,000 | Larger hood, ceiling duct routing; verify locally |
| Built-in / under-cabinet chimney | ₹18,000–45,000 | Plus the hood cabinet it hides inside; verify locally |
| Ducting, cowl and installation | ₹3,000–10,000 | Short, straight 150 mm duct; longer runs cost more |
Where chimney height is heading
Two shifts are quietly changing the height question. The first is the spread of induction and electric cooktops, which rise cooler than gas flames and let the hood sit a little lower, closer to the food, where capture is even better. As more Indian kitchens add an induction zone alongside gas, the sensible mounting height drifts towards the lower end of the band. The second is the arrival of auto-clean chimneys with heat and gesture sensors and variable-speed motors that boost suction when a burst of steam is detected, partly forgiving a slightly imperfect height — though no sensor rescues a chimney mounted at 950 mm.
Filter technology is moving the same way. Baffle filters, now standard, handle oily Indian cooking far better than the old mesh filters and tolerate the heat of a lower mounting; filterless auto-clean chimneys collect oil in a removable cup and ask only for an occasional wipe. None of this removes the need to get the height right — it only widens the margin for a well-mounted chimney. The brief has not changed since the roshandan: catch the smoke at the pan, before it reaches the room, and get it outside.
Eight rules for mounting a kitchen chimney
- Set the clearance to about 650–750 mm for gas, 550–650 mm for induction — measured to the lowest metal of the canopy.
- Decide the height before fixing the overhead cabinets, so the chimney is not forced up to match a cabinet line.
- Match the hood width to the hob: at least 600 mm for four burners, 900 mm for five burners or heavy frying.
- Keep the duct short, straight and at the maker's diameter; limit it to two gentle bends.
- Use rigid pipe on visible runs and fit a cowl outside that excludes rain and birds without choking the outlet.
- Anchor the bracket into brick or RCC with proper plugs — never into gypsum, hollow partition or loose plaster.
- Keep the gas cylinder in a ventilated cabinet and the chimney's socket to the side, earthed and off the heat line.
- Turn the ceiling fan off while cooking and avoid placing the hob in a strong window draught that deflects the plume.
Frequently asked questions about chimney height
What is the correct height of a chimney above a gas stove?
About 650 to 750 mm — roughly 26 to 30 inches — from the top of the hob to the underside of the chimney canopy. Around 700 mm is a safe default for a standard kitchen. Measure to the lowest metal of the hood, not to the filters recessed inside it.
Is it better to mount a chimney higher so it does not get dirty?
No. Mounting it higher keeps the metal cleaner only because it is catching less smoke — which defeats the purpose. A chimney above about 800 mm over a gas hob lets a large share of the fumes escape sideways. Keep it in the recommended band and clean the filters on schedule instead.
Can an induction chimney be placed lower than a gas one?
Yes. Because an induction or electric cooktop has no open flame, the rising air is cooler and the hood can sit at about 550 to 650 mm without scorching, which actually improves capture. Confirm the minimum for the specific model before mounting.
Does a longer duct mean the chimney should be mounted lower?
A long or twisting duct reduces the effective suction at the hood, so a chimney behind a bad duct behaves as though it were mounted too high. The fix is to shorten and straighten the duct rather than to drop the chimney below its sensible band. Keep the duct under about 3 metres with no more than two bends.
How high should the hood be for a tall person?
Comfort and capture both matter. For a tall cook, mount towards the upper end — about 750 mm over gas, or up to 800 mm for a built-in hob — so the head clears the canopy while the hood still sits within the capture zone. Pairing a wider 900 mm hood with the taller mounting keeps the smoke covered.
Sources & standards
- Bureau of Indian Standards — IS 3646 (Part 1): interior illumination and service areas, referenced for kitchen task areas
- National Building Code of India 2016, Part 8 (Building Services) and Part 11 (Approach to Sustainability) — ventilation of kitchens and service spaces
- National Building Code of India 2016, Part 4 (Fire and Life Safety) — clearances around cooking and gas appliances
- Neufert, Architects' Data — kitchen planning, extractor hood heights and clearances
- Kitchen chimney manufacturers' installation manuals (generic Indian market) — recommended hob-to-hood clearance and duct guidance
- Liquefied Petroleum Gas (Regulation of Supply and Distribution) guidance — domestic cylinder ventilation and placement
- Price ranges: indicative October 2026 estimates — confirm locally before budgeting



