Dado is one of those building words that everyone on an Indian site uses and few define. It means the tiling on the lower part of a wall — the band that protects the wall where water, splashes and knocks happen — and in kitchens and bathrooms it is some of the most important tiling in the house. Get its height right and the wall behind the counter and around the wash areas stays clean and dry for years; get it wrong and water finds the untiled plaster above the tiles, blows the paint, and grows the black mould that is the commonest complaint in Indian kitchens and toilets. The dado is cheap to extend by a few courses at the tiling stage and expensive to fix once the wall is damaged, so its height deserves a decision rather than a default.
The mistake is usually one of two. Either the dado is set too low — a single 450 mm band of tile above the kitchen counter that stops just where the real splashing starts, so the wall above the chimney and behind the tall taps gets wet — or the tiling is set too high everywhere out of caution, full height in rooms that do not need it, which wastes money and makes a small toilet feel like a clinic. The right answer is neither a habit nor a blanket rule but a height matched to where the water actually lands: higher behind a hob and a sink, lower behind a dry WC, full height in a wet shower. The water, not fashion, sets the line.
This article gives the dado and wall-tile heights that work in Indian kitchens and bathrooms: the kitchen dado height above the standard counter, full-height and half-height options and when each suits, the bathroom tiling heights for showers, WCs and basins, the splash dado where full tiling is not used, and the skirting that protects the floor-to-wall joint elsewhere in the home. The counter and fixture heights these tile heights relate to follow Indian practice and the dimension guides on this site, and the tile sizes assume the common Indian trade sizes.
Where the dado comes from
Tiling the lower part of a wall is an old idea that predates the ceramic tile. In traditional and colonial Indian buildings, the dado was often a band of oil paint, polished plaster or stone skirting running up the lower wall, protecting it from the scuffing of furniture, feet and the mopping water that washes across the floor. The word itself comes from classical architecture, where the dado is the body of a pedestal between its base and cornice, and it carried into building practice as the lower band of a wall treated differently from the upper. When glazed ceramic tiles became cheap and widespread, the wet and dirty parts of the house — the cooking wall, the bathing area, the wash place — were the first to be tiled, because tile is waterproof, wipeable and does not blow like paint. The dado height question is simply the modern form of an old instinct: protect the wall as high as the water and the wear reach.
The kitchen dado: 600 mm above the counter
The kitchen counter in Indian homes sits at about 850–900 mm above the finished floor. Above it, the wall is hit by water at the sink, oil and sauce at the hob, and splashes all along the working length. The standard kitchen dado tiles the wall from the top of the counter up by about 600 mm, which places the top of the dado at roughly 1450–1500 mm from the floor — high enough to catch the splashes that rise from a sink and a hob, and a comfortable band under the wall cabinets, whose underside is typically set at about 1400–1500 mm. That 600 mm band is the sensible minimum. Where there are no wall cabinets, or where a tall mixer tap or a filter throws water higher, the dado is often carried up further. Behind a hob in particular, the heat and the oil justify taking the tile higher than 600 mm, and many kitchens tile the full height behind the cooking zone even when the rest of the dado is 600 mm.
| Zone | Dado / tile height | Why |
|---|---|---|
| General counter run | ≈ 600 mm above the counter | Catches sink and working splashes; fills to wall cabinets |
| Behind the hob | Higher, often full height | Heat and oil rise above the 600 mm band |
| Behind the sink / tall tap | 600 mm, or higher if tap throws water | A filter or tall mixer splashes above the standard band |
| Open wall, no cabinets above | Often full height or 900–1200 mm | No cabinet to cap the dado; taller band looks resolved |
| Counter height itself | 850–900 mm finished | The datum the dado is measured from |
Full-height or half-height kitchen tiling
Beyond the standard 600 mm dado, two fuller options are common. A half-height treatment tiles from the counter to the underside of the wall cabinets and leaves the strip above the cabinets and the ceiling in paint — the economical, standard choice for most kitchens. A full-height treatment tiles the wall from counter to ceiling, or from floor to ceiling where there is no counter, which suits open kitchens, islands with a feature wall, and homes that want a seamless, wipeable cooking wall with no paint to blow. Full-height tiling costs more in material and labour but removes the vulnerable painted strip entirely and photographs well, which is why it is popular in open-plan apartments. The deciding factors are budget, whether the kitchen is open to a living area where the upper wall is seen, and how hard the kitchen is used — a serious daily-cooking Indian kitchen benefits from more tile, not less.
Bathroom tiling heights
Bathrooms are tiled higher than kitchens because water reaches higher and because the whole room is wet. The common Indian practice is to tile the walls to about 2100 mm — roughly door head height — which covers the shower zone, the taps and the splashing, and leaves only the strip above to the ceiling in a moisture-resistant paint or a false ceiling. Many bathrooms now tile full height, floor to ceiling, for a seamless waterproof box that is easy to clean and hides the pipework, and this has become the default in mid and upper-range work. The one zone that must always be tiled full height to the ceiling is the shower enclosure: wherever the shower spray reaches, the wall should be tiled with no painted band, because paint will not survive direct spray. Below all of this, the waterproofing membrane under the tiles — not the tile itself — is what actually keeps the water out, and it must be carried up the walls in the wet zones and never skimped.
| Zone | Tile height | Why |
|---|---|---|
| Shower enclosure / wet zone | Full height to ceiling | Direct spray; paint will not survive it |
| General bathroom walls | ≈ 2100 mm, or full height | Covers splashing; full height is the modern default |
| WC wall (no full tiling) | Splash dado ≈ 1200 mm | Protects against splash where the room is otherwise dry |
| Basin wall (no full tiling) | Splash dado ≈ 1000–1200 mm | Guards the wall around the basin and tap |
| Above the tiling to ceiling | Moisture-resistant paint or false ceiling | Low splash risk above door head |
Skirting: protecting the floor-to-wall joint
Away from the wet rooms, the lower wall is still protected, by a skirting — a short band of tile, stone or finished plaster at the bottom of the wall where it meets the floor. The skirting guards the vulnerable floor-to-wall joint from mop water, shoes, furniture and vacuum cleaners, and it hides the slightly rough junction where the floor finish meets the wall. A tiled or stone skirting in Indian homes is commonly about 75–100 mm high, cut from the floor tile so it matches, though taller skirtings of 100–150 mm are used for a more substantial look and in high-traffic areas. In rooms with wooden or laminate flooring the skirting also covers the expansion gap the floor needs at the wall. The skirting is a small element, but a missing or badly finished skirting is where a wall first gets dirty and damaged, so it is tiled or finished as part of the same job, not left as an afterthought. A skirting can be flush with the plaster, sit slightly proud, or be grooved in as a shadow line; the flush detail looks neatest but needs careful plastering, while a proud skirting is easier to fit and hides a less-than-perfect wall base.
Tile sizes, setting out and cost
The tile size quietly controls how a dado looks. Common Indian wall tiles come in sizes such as 300 × 450 mm, 300 × 600 mm and 250 × 375 mm, and the dado height should be set out so the top course is a sensible cut, not a thin sliver. A 600 mm dado of 300 × 600 mm tiles laid on end, or two courses of 300 mm tiles, sits cleanly; an awkward height leaves an ugly 40 mm strip at the top. Good tilers set out the dado from the top down, so the full tiles land where they are seen and any cut goes low or is hidden under a cabinet. On cost, tile material is the cheaper part of a tiled surface — the laying labour, adhesive, grout and waterproofing often match or exceed it. Indicative October 2026 material bands are roughly ₹40–80 per sq ft for ceramic wall tiles and ₹60–120 and up for vitrified, with laying labour around ₹25–40 per sq ft, plus the waterproofing beneath in wet areas. The table collects the figures.
Three finishing details separate a neat dado from a rough one. The grout line is the first: a narrow, evenly spaced joint in a colour chosen to suit the tile, filled with a good grout, keeps water out and looks deliberate, while a wide, uneven or wrongly coloured joint spoils even an expensive tile. External corners are the second: where tiling turns an outside corner, a mitred edge or a slim metal or PVC trim gives a clean, chip-resistant arris, far better than two raw tile edges butted together. The junction where the dado meets the painted wall above is the third: a straight, level top line — often finished with a slim edging trim or a bull-nosed tile — makes the dado read as a designed band rather than as tiling that simply ran out. None of these cost much, but they are the difference between tiling that looks fitted and tiling that looks stuck on, and they should be specified rather than left to chance on site.
| Item | Indicative cost (October 2026) | Notes |
|---|---|---|
| Ceramic wall tiles (material) | ₹40–80 per sq ft | 300 × 450 / 300 × 600 digital glaze common |
| Vitrified / designer wall tiles (material) | ₹60–120+ per sq ft | Larger formats and designer ranges higher |
| Tile laying labour | ₹25–40 per sq ft | Waterproofing and screed extra in wet areas |
| Skirting tile | From the floor tile; cutting labour | Usually cut from the floor tile to match |
| Waterproofing (wet areas) | Part of civil work; verify locally | Under the tile; the real protection |
Where wall tiling is going
The clear trend is towards larger tiles and more full-height tiling. Large-format wall tiles and slim porcelain slabs mean fewer grout lines, which look cleaner and, more usefully, give water fewer paths into the wall — a 600 × 1200 mm panel behind a hob has a fraction of the joints of small tiles. Full-height bathroom tiling has become the default in new work, treating the bathroom as a seamless waterproof box. Digital printing has made tiles that convincingly imitate marble, stone and concrete, so the look is no longer tied to the material, and anti-skid finishes for floors and matt finishes for walls have improved. At the same time, feature bands and mosaics let a dado be decorative as well as protective. None of this changes the underlying logic: tile as high as the water and wear reach, waterproof beneath, and set the heights out so the tiling looks deliberate — the materials get better, the heights stay governed by where the water lands.
| Era | Lower-wall protection | What changed |
|---|---|---|
| Traditional / colonial | Oil-paint dado, polished plaster, stone skirting | Protected the lower wall before ceramic tile |
| Mid-20th century | Small glazed ceramic tiles in wet zones | Cheap waterproof tiling reached kitchens and baths |
| Late 20th century | Standard 600 mm kitchen dado, bath to 2.1 m | Settled heights matched to splashing |
| 2000s–2010s | Full-height bathroom tiling, larger formats | Seamless waterproof boxes; fewer grout lines |
| 2020s onward | Slim porcelain slabs, digital stone looks | Minimal joints; any look on a waterproof body |
Frequently asked questions
What is the standard kitchen dado height?
The standard kitchen dado tiles the wall about 600 mm above the counter, which sits at 850–900 mm, putting the top of the dado at roughly 1450–1500 mm — filling the gap to the wall cabinets, whose underside is typically 1400–1500 mm. Behind the hob the tiling is usually taken higher, often full height, because heat and oil rise above the 600 mm band.
How high should bathroom walls be tiled?
Bathroom walls are commonly tiled to about 2100 mm, roughly door head height, or full height to the ceiling, which has become the modern default. The shower enclosure should always be tiled full height to the ceiling, because direct spray will destroy any painted band. Where a WC or basin wall is otherwise dry, a splash dado of about 1200 mm can be enough.
What is a splash dado?
A splash dado is a lower band of tiling — commonly about 1200 mm high — used on a wall that does not get full tiling, to protect it against the splashing around a WC or a wash basin. It is the economical way to protect a dry-ish wall without tiling the whole room, and it is set out so the top course is a clean tile, not a thin cut.
How high should skirting be?
A tiled or stone skirting in Indian homes is commonly about 75–100 mm high, cut from the floor tile so it matches, with taller skirtings of 100–150 mm used for a more substantial look or in high-traffic areas. It protects the floor-to-wall joint from mop water, shoes and furniture, and in rooms with wooden or laminate flooring it also covers the floor's expansion gap at the wall.
Is full-height tiling worth it?
Full-height tiling costs more in material and labour but removes the vulnerable painted strip above the tiles entirely, gives a seamless wipeable surface, and photographs well — which is why it has become the default in bathrooms and in open kitchens. In a hard-used daily-cooking kitchen or a family bathroom it is usually worth it; in a low-use guest toilet, tiling to 2100 mm with good paint above can be enough.
Sources & standards
- National Building Code of India 2016 — Part 9: Plumbing Services, and Part 6: Structural design (wet-area and finishes guidance)
- Bureau of Indian Standards — IS 15622 (pressed ceramic tiles) and IS 13630 (methods of test for ceramic tiles)
- Bureau of Indian Standards — IS 15658 and allied standards for tiling and laying practice
- Neufert, Architects' Data; Time-Saver Standards — counter, fixture and tiling heights
- Tile and adhesive manufacturers' standard sizes and laying recommendations, described generically
- Price ranges: indicative October 2026 estimates — confirm locally before budgeting



