← All articles

Lighting · 04 Nov 2026 · 19 min read

Home Inverter and Battery Sizing for Indian Homes

Home Inverter and Battery Sizing for Indian Homes — cover

The inverter is the one home purchase that families routinely get wrong in both directions. Some buy far too little — an 800 VA unit asked to run a home that trips it the moment the fridge and the microwave come on together. Others buy far too much — a 2.5 kVA system with two big batteries for a flat that only needs a few lights and fans to ride out a short cut. Both mistakes cost money: the first in a backup that fails when it is needed, the second in batteries that sit half-charged, age early and take up a corner of the house for no reason.

The confusion comes from shopping by the wrong number. Showrooms sell inverters by a flat size — "this one is for a 2BHK" — when the correct basis is the actual electrical load the family wants to keep running during a power cut, and for how long. A 2BHK that only needs lights, fans and a television during a cut has a very different load from a 2BHK that wants the fridge, the Wi-Fi, a water pump and a bedroom air-conditioner to stay on. The flat size tells you almost nothing; the appliance list tells you everything.

This article turns inverter and battery sizing into the three-step calculation that electrical engineers actually use. First, add up the load in watts. Second, convert that to a VA rating and choose the inverter. Third, choose the battery in amp-hours from the number of backup hours wanted. It then compares battery types and their costs, explains where and how to install the system safely, and sets out where home backup is heading as lithium and solar hybrids arrive. The figures follow standard electrical practice and manufacturers' typical ranges, adapted to Indian homes.

From load-shedding to lithium: how home backup grew up

Home backup power in India was born out of unreliable supply. For decades, scheduled load-shedding and unplanned cuts were a daily fact in most towns, and the first answers were crude: a car battery wired to a simple square-wave inverter, or a noisy petrol generator on the balcony. Through the 1990s and 2000s the sine-wave home inverter — a quiet box on the wall paired with a tall tubular battery under it — became the standard, and the tubular lead-acid battery, designed for the deep, slow discharge a home needs, became its natural partner.

Two things are changing that settled picture. Grid supply in most Indian cities is far better than it was, so many homes now need backup only for short, occasional cuts rather than hours every day — which changes the sizing towards smaller batteries. At the same time, lithium iron phosphate (LiFePO4) batteries and integrated lithium inverter units are arriving in homes, offering longer life, far less maintenance, faster charging and a much smaller footprint, at a higher upfront price. And rooftop solar is turning the home inverter into a hybrid that charges from the sun by day and the grid at night. The calculation below works the same way whichever battery chemistry is chosen.

Fig. 1 — How a home inverter system works GRID230 V AC CHARGER& changeover BATTERY12 / 24 V DC INVERTERDC → AC HOMElights, fans… mains passes straight through when supply is present When the grid is on, it powers the home and charges the battery. When it fails, the inverter turns battery DC into 230 V AC within milliseconds. The VA rating sizes the inverter; the amp-hour rating sizes how long the battery lasts.
Fig. 1 — How a home inverter system works (block diagram)

Step 1 — add up the load you want to run

The first and most important step is to list only the appliances that must stay on during a cut, and add up their running power in watts. This is the "connected backup load", and it is almost always much smaller than the home's total connected load, because heavy appliances — the geyser, the oven, most air-conditioners, the washing machine's heater — are deliberately left off the backup. A common mistake is to size for everything; the right approach is to size for the essentials and treat anything heavier as a conscious, separate decision. The table gives typical running figures for Indian household appliances.

ApplianceTypical running powerOn backup?Note
LED bulb / tube8–20 W eachYesA whole home of LEDs is only 100–200 W
Ceiling fan50–75 W eachYesBLDC fans draw about half of this
Television + set-top box80–150 WYesFlat panels are modest; projectors more
Wi-Fi router / ONT10–20 WYesSmall but valued during a cut
Refrigerator100–250 W runningUsuallyCompressor surge 2–3× at start-up
Mixer / microwave500–1200 WRarelyShort bursts; a big spike if included
Water pump (0.5 HP)approx 400 WSometimesSurge at start is 2–3× running
Air-conditioner (1 ton inverter)900–1400 WOnly on large systemsNeeds a high-VA inverter and big battery

Add the running watts of everything marked "yes" for the home in question. A small flat that keeps six LED lights, three fans, a television, a router and a refrigerator on backup totals roughly 650 to 800 W. A larger home that adds more lights, more fans and a water pump reaches 1200 to 1600 W. Keep a note of which appliances have a start-up surge — the refrigerator compressor and any pump draw two to three times their running figure for a fraction of a second when they switch on — because the inverter has to survive that surge, not just the steady load.

Fig. 2 — A small home's backup load 6 LED lights 3 ceiling fans TV + set-top Wi-Fi router Refrigerator TOTAL 120 W 210 W 120 W 20 W 180 W approx 650 W running Add only the appliances that must run during a cut. The fridge compressor surges to 2–3× at start-up, so the inverter must be chosen for the peak, not just this steady total. Heavy loads — geyser, oven, big AC — are left off backup.
Fig. 2 — Adding up a small home's backup load (running watts)

Step 2 — size the inverter (the VA rating)

Inverters are rated in volt-amperes (VA), not watts, and the two are related by the power factor — a measure of how "real" the load is. For a typical mix of Indian household appliances the power factor sits around 0.7 to 0.8, so the VA rating needed is the running watts divided by about 0.7. A 650 W load therefore needs roughly 930 VA, which points to a 1000 to 1100 VA inverter. Sizing it this way leaves headroom for the start-up surge and keeps the inverter running comfortably below its limit, where it is most efficient and runs coolest. The table turns common load totals into inverter sizes.

Running load (W)VA needed (÷ 0.7)Choose inverterTypical homeSystem voltage
up to 500 Wapprox 700 VA800–900 VA1BHK, lights-fans-TV12 V
500–750 Wapprox 1000 VA1000–1100 VASmall 2BHK with fridge12 V
750–1100 Wapprox 1450 VA1500 VALarger 2BHK / 3BHK12 V or 24 V
1100–1700 Wapprox 2300 VA2.5 kVA3BHK with pump24 V
1700–2800 Wapprox 3700 VA3.5–5 kVALarge home / small AC24 V or 48 V

Two rules keep this honest. First, always buy one size above the bare calculation, so the inverter is not running flat out — an inverter run continuously near its ceiling overheats and ages quickly. Second, check the surge rating, usually quoted as a peak the inverter can hold for a second or two; it must comfortably exceed the combined start-up surge of the fridge and any pump on the backup. A pure sine-wave inverter is worth the small premium for any home with a fridge, a modern television or sensitive electronics, because the cleaner waveform runs motors cooler and avoids the hum and heat a square-wave unit causes. A modified or square-wave inverter may cost a little less, but it can make fans buzz, dim some LED drivers and run a refrigerator compressor hotter over time, which rarely saves money in the end.

Step 3 — size the battery (the amp-hours)

The inverter decides how much the system can run at once; the battery decides how long. Battery capacity is measured in amp-hours (Ah) at the system voltage. The usable energy is the capacity multiplied by the voltage and by the usable depth of discharge, less inverter losses. A useful working formula for a lead-acid system is: backup hours ≈ (battery Ah × battery volts × 0.8 × 0.8) ÷ load in watts, where the first 0.8 is the usable depth of discharge and the second is the round-trip efficiency. For a 150 Ah, 12 V battery running a 650 W load, that is about (150 × 12 × 0.8 × 0.8) ÷ 650 ≈ 1.8 hours. The table reads this out for common pairings.

Fig. 3 — Backup hours vs load (150 Ah, 12 V) 6 h 3 h 0 200 400 W 600 800 approx 2.9 h at 400 W Load drawn by the home (watts) Backup (hours) Backup falls steeply as the load rises. To double the hours, either halve the load or double the battery capacity.
Fig. 3 — Backup hours against load for one 150 Ah, 12 V battery
BatteryAt 300 W loadAt 500 W loadAt 800 W loadGood for
100 Ah, 12 Vapprox 2.5 happrox 1.5 happrox 1 h1BHK, short cuts
150 Ah, 12 Vapprox 4 happrox 2.3 happrox 1.4 hSmall 2BHK, the common choice
200 Ah, 12 Vapprox 5 happrox 3 happrox 1.9 h2–3BHK, longer cuts
2 × 150 Ah, 24 Vapprox 8 happrox 4.8 happrox 3 h3BHK, long rural cuts

The table makes the trade-off visible: backup hours fall steeply as the load rises, so the cheapest way to get more hours is often to cut the load — swap to BLDC fans, leave the fridge off at night — rather than buy a bigger battery. It also shows why two batteries in series (giving 24 V) suit homes that both draw a large load and want long backup: the higher voltage lets the same wires carry more power with less loss, and the paired capacity gives the hours. Lead-acid batteries should not be discharged below about 20 per cent of capacity regularly, which is why the usable depth of discharge in the formula is 0.8, not 1.0; draining them flat shortens their life sharply.

Battery types compared: tubular, flat-plate and lithium

The battery is where the money goes and where the choices matter most. Three chemistries dominate Indian homes. Flat-plate lead-acid is the cheapest and suits homes with rare, short cuts. Tubular lead-acid is the long-standing favourite for homes with regular cuts, because its construction tolerates the deep, repeated discharges a home demands and it lasts longer. Lithium iron phosphate is the newcomer: two to three times the price upfront, but far longer life, almost no maintenance, a much smaller and lighter package, faster charging and a deeper usable discharge. The table compares them with indicative October 2026 prices, which vary with brand, capacity and city and should be confirmed locally before budgeting.

Battery typeTypical lifeMaintenanceIndicative costBest for
Flat-plate lead-acid (150 Ah)2–3 yearsTop-up water periodically₹10,000–15,000Rare, short cuts; tight budgets
Tubular lead-acid (150 Ah)4–6 yearsTop-up water occasionally₹13,000–20,000Regular cuts; the common choice
Tubular lead-acid (200 Ah)4–6 yearsTop-up water occasionally₹18,000–26,000Longer backup, larger homes
Lithium (LiFePO4, approx 2.5 kWh)8–12+ yearsEssentially none₹55,000–1,00,000+Long life, small footprint, solar
Inverter, pure sine 1500 VA6–10 yearsMinimal₹9,000–16,000Pairs with the battery above

Where and how to install it safely

A lead-acid inverter battery vents a small amount of hydrogen while charging, so it must sit in a ventilated spot, never in a sealed cupboard or a bedroom. The usual place is a utility area, a service balcony or a lobby, on a battery trolley that keeps it off the floor and allows air around it. The inverter itself is wall-mounted nearby, out of reach of water and direct sun, with clearance around it to shed heat. The two are joined by short, thick cables — long or thin cables waste power as heat and can sag the voltage — and the whole system is connected through the home's distribution board on a dedicated backup circuit, so only the chosen lights and sockets are backed up.

Fig. 4 — Inverter & battery placement 1200–1500 100 min air gap 150–200 INVERTER BATTERY on trolley Keep in a ventilated utility, balcony or lobby — never a sealed cupboard or bedroom. Short, thick cables between the two. Out of water and direct sun. Lead-acid batteries vent hydrogen while charging, so they need air around them; a trolley keeps them off the floor.
Fig. 4 — Inverter and battery placement with clearances (elevation, mm)

Where home backup is going

The direction of travel is clear: smaller, cleaner and smarter. Lithium batteries are falling in price each year and already make sense for homes that want long life, a small footprint and freedom from water top-ups. Integrated units that combine a lithium battery and a sine-wave inverter in one wall-mounted box are turning a bulky corner installation into a slim appliance. Rooftop solar is turning the home inverter into a hybrid that charges from the sun by day, stores the surplus and draws from the grid only when needed — which changes the sizing question from "how many hours of backup" to "how much of the day can run on stored sun". The three-step method survives all of this: list the load, size the converter, size the store.

EraTypical systemBatteryWhat it solved
1990sSquare-wave inverter + car batteryAutomotive lead-acidLights and a fan through a cut
2000sSine-wave inverter + tubular batteryTubular lead-acidClean power for TV, fridge, electronics
2010sHigher-VA inverter, twin batteriesTubular lead-acidLonger backup for bigger homes
2020sLithium integrated unitLiFePO4Long life, small size, no maintenance
NextSolar hybrid inverterLithium + solarRuns the day on stored sun, grid as backup

Rules for sizing a home inverter and battery

  • Size from the appliances you will actually run during a cut, never from the size of the flat.
  • Add the running watts, then divide by about 0.7 to get the VA rating the inverter needs.
  • Buy one inverter size above the bare figure so it never runs flat out, and check the surge rating against the fridge and pump.
  • Choose a pure sine-wave inverter for any home with a fridge, a modern TV or sensitive electronics.
  • Size the battery in amp-hours from the backup hours wanted, using the (Ah × V × 0.8 × 0.8) ÷ watts rule.
  • Do not drain lead-acid batteries below about 20 per cent regularly, and never mix old and new or different capacities.
  • Place the battery in a ventilated spot on a trolley, and join it to the inverter with short, thick cables.
  • Back up only a dedicated circuit of chosen lights and sockets, not the whole house.

Frequently asked questions

What size inverter do I need for a 2BHK?

It depends on what the 2BHK runs during a cut, not on its being a 2BHK. A 2BHK that keeps lights, fans, a TV, Wi-Fi and a fridge on draws about 650 to 800 W and needs roughly a 1000 to 1100 VA inverter. Add a water pump or more appliances and it rises to 1500 VA. Add an air-conditioner and it needs 2.5 kVA or more with a large battery.

How is VA different from watts?

Watts measure the real power an appliance uses; VA measures the apparent power the inverter must supply, which is larger because of the power factor. For a typical home mix the power factor is about 0.7 to 0.8, so the VA rating needed is the running watts divided by about 0.7. A 700 W load needs roughly a 1000 VA inverter.

How many hours of backup will I get?

Use backup hours ≈ (battery Ah × battery volts × 0.8 × 0.8) ÷ load in watts. A 150 Ah, 12 V battery running a 400 W load gives about (150 × 12 × 0.8 × 0.8) ÷ 400 ≈ 2.9 hours; the same battery at 650 W gives under two hours. To double the hours, halve the load or double the capacity.

Is a lithium battery worth the extra cost?

For a home with frequent cuts or rooftop solar, often yes: lithium lasts two to four times longer, needs no water top-ups, charges faster, discharges deeper and takes far less space, which offsets much of the higher upfront price over its life. For a home with rare, short cuts and a tight budget, a tubular lead-acid battery is still the sensible, lower-cost choice.

Sources & standards

  1. National Building Code of India 2016, Part 8, Section 2 (Electrical and Allied Installations) — wiring, distribution and safety
  2. Bureau of Indian Standards — IS 13010 and IS 15549 (stationary and VRLA lead-acid batteries) and IS 16046 (lithium battery safety)
  3. Central Electricity Authority (Measures relating to Safety and Electric Supply) Regulations — general installation safety
  4. Neufert, Architects' Data — building services and plant-room ventilation guidance
  5. Inverter and battery manufacturers' published VA, surge and amp-hour specifications (generic trade ranges)
  6. Price ranges: indicative October 2026 estimates — confirm with a local supplier before budgeting
Discuss your project