← All articles

Lighting · 03 Nov 2026 · 20 min read

Home Water Systems: Overhead Tank, Pressure and Pump Sizing

Home Water Systems: Overhead Tank, Pressure and Pump Sizing — cover

Almost every Indian home runs on the same quiet machine, and almost no one draws it. Municipal water arrives for an hour or two a day, at low and unreliable pressure, so it is caught in an underground tank, lifted by a pump to an overhead tank on the roof, and then fed to the taps by gravity. It is a simple, robust system that has served Indian cities for decades — and it is also the source of the two most common water complaints in any home: the shower that dribbles on the top floor, and the pump that runs far too often or never seems to stop. Both problems are almost always about sizing and pressure, not about buying a bigger motor.

The confusion starts because people think about water in terms of the pump, when the thing that actually drives a gravity-fed tap is head — the vertical height of water above it. A tap gets its pressure from how far the overhead tank sits above it, not from the pump that filled the tank hours earlier. A powerful pump fills the tank faster but adds nothing to the pressure at the shower. That single misunderstanding leads homeowners to replace a perfectly good pump, enlarge it, and still get a weak top-floor shower, because the real problem — too little height, or too thin a pipe — was never touched.

This article treats the home water system as a whole. It sizes the underground and overhead tanks against the number of people in the house, explains head and pressure in plain numbers a homeowner can use, sizes the pump for the actual lift and the actual pipe, and shows when a pressure pump or a pressurised system genuinely helps and when it is money wasted. The figures follow common Indian practice and the plumbing provisions of the National Building Code; exact local water rules and the advice of a plumber should always be confirmed before anything is built.

How the Indian home water system works

The standard arrangement has four parts working in sequence. Water from the municipal main, a borewell or a tanker first enters an underground tank, usually built in RCC below the ground floor or the driveway, which stores a day or two of supply so the house is not left dry when the main runs for only an hour. A pump — typically a monoblock or a submersible — then lifts that water up to an overhead tank, almost always moulded polyethylene, sitting on the roof or a raised staging. From the overhead tank, water falls by gravity through the home's pipes to every tap, cistern, geyser and shower. A float valve or an automatic level controller switches the pump off when the overhead tank is full, so the system is largely hands-off once it is set up correctly.

Each part has a clear job, and problems come from getting one of them wrong. Too small an underground tank and the house runs dry between supply hours. Too small an overhead tank and the pump cycles on and off all day, wearing out. Too little height under the overhead tank and the lower pressure at the top-floor taps disappoints. Too thin a distribution pipe and even a well-filled, high-mounted tank cannot push a strong shower, because the water loses its energy to friction on the way down. The art of a good water system is balancing these four so the house always has water, the pump runs rarely, and every tap feels strong.

Fig. 1 — The standard home water system Overhead tank (roof) Underground tank pump pump lifts water up gravity feed down to taps upper taplower tap The pump only fills the roof tank; the pressure at every tap comes from gravity — the height of water above it.
Fig. 1 — The standard home water system (schematic)

Sizing the tanks

Tank sizing starts from how much water a household uses in a day. Indian practice and the National Building Code work to a figure of roughly 135 litres per person per day for a home with full plumbing, covering drinking, cooking, bathing, washing and sanitation. For a family of five that is about 675 litres a day of actual use. The two tanks are then sized around that daily figure but for different jobs: the underground tank stores a buffer against the municipal supply stopping, so it is usually sized for one to two full days; the overhead tank only needs to hold enough to get through the gaps between pump cycles and the peak morning demand, so it is smaller, typically about half a day to a full day of use.

In round numbers that a plumber will recognise, a family of four to five is well served by an underground tank of about 1,000 to 2,000 litres and an overhead tank of about 500 to 1,000 litres. Homes with unreliable supply, a borewell that runs only at certain hours, or a garden to water, size the underground tank larger. The overhead tank should not be oversized without thought: a huge roof tank adds dead weight to the structure, lets water stand and stagnate, and does nothing for pressure. The table below gives sensible starting sizes by household; the final figures should be adjusted for local supply reliability and confirmed with a plumber.

HouseholdDaily use (approx)Underground tankOverhead tank
1–2 people270–350 litres750–1,000 litres300–500 litres
3–4 people400–550 litres1,000–1,500 litres500–750 litres
5–6 people675–800 litres1,500–2,000 litres750–1,000 litres
7–8 people950–1,100 litres2,000–3,000 litres1,000–1,500 litres
Fig. 2 — Head drives the tap (1 m ≈ 0.1 bar) tank water level tap A — 3 m headtap B — 6 m headtap C — 9 m head 0.3 bar0.6 bar0.9 bar A rain shower wantsabout 1.0–1.5 bar —roughly 10–15 m ofhead above the head. Every metre the tank sits above a tap adds about 0.1 bar. The top-floor tap, closest to the tank, has the least head.
Fig. 2 — Head and pressure: height drives the tap

Head and pressure in plain numbers

Pressure in a gravity system is easy to estimate once one rule is known: every metre of vertical height between the water surface in the overhead tank and the tap gives about 0.1 bar of pressure. So a tap three metres below the tank sees roughly 0.3 bar; six metres gives 0.6 bar; ten metres gives 1.0 bar. This height is called the static head, and it is the whole story of why pressure varies around a house. The ground-floor taps, far below the roof tank, feel strong; the top-floor taps, close under the tank, feel weak — the opposite of what people expect, because they are thinking about the pump rather than the height.

Now compare that against what fittings actually want. An ordinary tap works happily at half a bar. A good overhead shower or a rain shower wants about one to one and a half bar to feel strong, which means ten to fifteen metres of head above it. A top-floor bathroom with the tank only two or three metres above it therefore gets a weak shower no matter how big the pump is, because the pump does not set the pressure — the height does. This is why the single most effective pressure fix in many homes is to raise the overhead tank on a taller staging, and why the second is to fit a pressure pump at the top-floor bathroom, not to enlarge the filling pump down at the sump.

Why the shower is weak

When a top-floor shower is weak, there are only a handful of real causes, and the pump is rarely one of them. The first and commonest is too little head: the tank is not high enough above that bathroom, so there simply is not enough pressure. The second is an undersized or over-long pipe: water loses energy to friction as it flows, and a long run through a thin pipe, past many bends and a half-closed valve, arrives weak even when the head is adequate. The third is a clogged aerator, cartridge or shower head — mineral scale and debris choke the fitting itself. The fourth is air or a partly shut valve in the line. A methodical check of these, in order, solves most weak-shower complaints without buying anything large.

The pipe size matters more than homeowners expect. A 15 millimetre (half-inch) branch is fine for a single tap but struggles to feed a rain shower; a 20 or 25 millimetre feed carries far more water with far less friction loss, which is why good plumbing drops a larger main down from the tank and only reduces to 15 millimetre at the last short branch to each fitting. Running everything in thin pipe to save a little material is a false economy that shows up as weak showers for the life of the house. Where the head genuinely cannot be increased — a flat roof, a top-floor bathroom right under the tank — a small pressure pump on that line is the correct and inexpensive answer.

FittingComfortable pressureHead needed (approx)Typical pipe feed
Basin / kitchen tap0.3–0.5 bar3–5 m above tap15 mm branch
WC cistern / flush0.2–0.5 bar2–5 m above tap15 mm branch
Overhead shower1.0–1.5 bar10–15 m above tap20 mm feed, 15 mm last
Rain / body shower1.2–2.0 bar12–20 m or pump20–25 mm feed
Geyser (storage)0.3–0.8 bar3–8 m above tap15–20 mm branch

Pipe size is the quiet decider between a strong and a weak tap, because water loses energy to friction as it flows and a thin pipe loses far more than a thick one. The table below gives the common distribution sizes and the job each does. The principle a good plumber follows is to keep the feed generous down from the tank and reduce to the small 15 millimetre branch only for the last short run to a single fitting, so that no shower is starved by a long, thin pipe carrying water past many bends.

Pipe size (nominal)CarriesFriction lossUse
15 mm (½ inch)One tapHigh over long runsLast short branch to a fitting
20 mm (¾ inch)A shower or two tapsModerateFeed to a bathroom
25 mm (1 inch)Several fittingsLowRiser and main distribution
32 mm and aboveWhole floor / houseVery lowPump riser, large homes

Sizing the filling pump

The pump that lifts water from the underground tank to the roof has one job: to fill the overhead tank in a reasonable time against the real lift and the real pipe. Its two numbers are head and flow. The head it must overcome is the vertical lift from the sump to the top of the overhead tank, plus the friction losses in the riser pipe and fittings — a rough rule is to add about twenty to thirty per cent to the simple vertical height to allow for friction. The flow decides how fast the tank fills. For a typical home, a small monoblock pump of modest horsepower moving water up two or three floors through a 25 millimetre riser is ample; bigger is not better, because an oversized pump fills the tank in a flash, cycles off, and then starts again at the next draw-off, wearing itself and the switchgear.

A sensible approach is to match the pump to the lift, not to a vanity figure. A ground-plus-two home lifting water perhaps ten to twelve metres needs a pump rated comfortably above that total head at a flow that fills the roof tank in ten to twenty minutes. Fitting an automatic level controller stops the pump dry-running when the sump empties and switches it off when the roof tank is full, which protects the motor and ends the daily ritual of someone remembering to switch it on and off. The filling pump has nothing to do with tap pressure; that comes from the height of the tank it fills. Keeping those two roles separate in one's head prevents most wrong purchases.

Fig. 3 — Pump head = vertical lift + friction roof tank topsumppump vertical lift(sump to tank) add 20–30% for frictionin pipe and fittings Total head the pump must beat = vertical lift + friction allowance. Size for this, and aim to fill the tank in 10–20 min.
Fig. 3 — Sizing the filling pump: lift plus friction

When a pressure pump helps

A pressure pump — sometimes a small inline booster, sometimes a pressurised hydro-pneumatic system with a bladder tank — raises the pressure at the taps, which is a different job from filling the overhead tank. It is the right answer in exactly the situations where head cannot be fixed: a top-floor bathroom sitting right under the roof tank, a flat-roofed house where the tank cannot be raised much, or a whole house that wants strong rain showers everywhere. A small booster on the shower line, triggered by flow, lifts that one weak shower to a satisfying one to one and a half bar. A whole-house pressurised system holds the entire home at a set pressure regardless of which floor the tap is on, and is increasingly specified in larger homes and villas.

What a pressure pump cannot do is substitute for storage or for an undersized pipe. Boosting pressure through a pipe too thin to carry the flow simply moves the bottleneck; the pipe must be sized for the flow first. And a booster on a line with no water behind it — an empty overhead tank — achieves nothing. The correct order is always the same: get the storage and the head right, size the pipes for the flow, and only then add a booster where the head genuinely cannot be raised. Added in that order, a pressure pump is a cheap and transformative fix; added as a first reflex, it often disappoints because the real limit was elsewhere.

ProblemLikely causeRight fixWrong fix
Weak top-floor showerToo little headRaise tank or add boosterBigger filling pump
All taps weakUndersized pipe / low tankLarger feed pipe, higher tankMore pump horsepower
Pump runs all dayOversized pump, small tankRight-size pump, level controllerReplace with bigger pump
House runs drySmall underground tankLarger sump storageBooster pump
One tap weakClogged aerator / cartridgeClean or replace fittingWhole-house booster
Fig. 4 — Overhead tank capacity by household (litres) 1–2 people3–4 people5–6 people7–8 people 300–500500–750750–10001000–1500 Overhead tanks stay modest; the underground tank carries the one-to-two-day buffer. Oversizing adds dead weight.
Fig. 4 — Overhead tank capacity by household (litres)

Where home water is going

Home water systems are slowly getting smarter and more efficient, though the underlying gravity logic is not going away. Automatic level controllers are now standard and are being joined by water-level sensors that send a phone alert, leak detectors that cut the supply, and timers that fill tanks during off-peak hours. Pressurised whole-house systems, once a luxury-villa feature, are moving into ordinary multi-storey homes as rain showers become normal. Rainwater harvesting, now mandated in many Indian cities for larger plots, adds a recharge or storage loop to the system. Dual plumbing — separating potable water from flushing and gardening water drawn from harvested rain or treated greywater — is appearing in new green-rated homes. None of this changes the four basic parts; it makes them run with less waste and less daily attention, which is exactly where a well-planned home water system should be heading.

Rules for a water system that just works

  • Size the underground tank for one to two days of use so the house never runs dry between supply hours.
  • Keep the overhead tank modest — half a day to a day — to avoid dead weight and standing water.
  • Remember that tap pressure comes from the tank height, not the filling pump.
  • For strong showers, aim for ten to fifteen metres of head, or raise the tank on a taller staging.
  • Run a larger feed pipe down from the tank and reduce to 15 mm only at the last branch.
  • Match the filling pump to the real lift plus a friction allowance; fit an automatic level controller.
  • Add a pressure pump only after storage, head and pipe size are right, and only where head cannot be raised.
  • Check aerators, cartridges and valves first when one fitting is weak — it is usually a small blockage.

Frequently asked questions

What size water tank does a family of four need?

Working from roughly 135 litres per person per day, a family of four uses about 400 to 550 litres a day. A sensible underground tank is about 1,000 to 1,500 litres, giving a buffer of a day or two against the municipal supply stopping, and an overhead tank of about 500 to 750 litres, enough to cover the morning peak and the gaps between pump cycles. Homes with unreliable supply or a garden should size the underground tank larger.

Will a bigger pump increase my water pressure?

No — not at the taps. The filling pump only lifts water into the overhead tank; the pressure at each tap comes from the height of that tank above the tap, at about 0.1 bar per metre. A bigger filling pump fills the tank faster and may cycle more often, but it adds nothing to shower pressure. To raise pressure you raise the tank, enlarge the feed pipe, or fit a pressure pump on the weak line.

How high should the overhead tank be?

As high as practical above the highest tap you want to feel strong. Every metre adds about 0.1 bar. For ordinary taps, two or three metres of head is enough; for a good overhead shower, aim for ten to fifteen metres, which usually means the tank must sit well above the top-floor bathroom. Where that height is impossible, a small pressure pump on the shower line does the same job.

Do I need a pressure pump?

Only if the head cannot be raised and the taps are still weak after the pipe size is correct. A pressure pump is the right fix for a top-floor bathroom directly under the tank, a flat-roofed house, or a home that wants strong rain showers throughout. It is the wrong first reflex if the real problem is a small tank, a thin pipe or a clogged fitting, because boosting pressure through an undersized pipe just moves the bottleneck.

Why does my pump switch on and off constantly?

Usually because the pump is oversized for the overhead tank, or because the tank is too small, so it fills in moments and then restarts at the next draw-off. The fix is to match the pump to the lift rather than over-specifying it, and to fit an automatic level controller that switches the pump off when the tank is full and prevents it dry-running when the sump is empty. Short, frequent cycling wears out both the motor and the switchgear.

Sources & standards

  1. Bureau of Indian Standards — IS 2065 (code of practice for water supply in buildings): tank sizing, pipe sizing and distribution
  2. National Building Code of India 2016, Part 9 (plumbing services) — water supply, storage and pumping
  3. Bureau of Indian Standards — IS 12183 (code of practice for plumbing in multi-storeyed buildings) and IS 4985 (uPVC pipes) for distribution
  4. Central Public Health and Environmental Engineering Organisation (CPHEEO) — Manual on Water Supply, per-capita demand figures
  5. Neufert Architects' Data and Time-Saver Standards — plumbing, pressure, head and pump sizing fundamentals
  6. Pump and tank manufacturer technical data — described generically, head, flow and level-controller guidance
  7. Price ranges: indicative October 2026 estimates — confirm with a local plumber before budgeting
Discuss your project