← All articles

Kitchen · 07 Nov 2026 · 24 min read

Kitchen Chimney Selection and Ducting in India

Kitchen Chimney Selection and Ducting in India — cover

The kitchen chimney is the one appliance in an Indian kitchen that is bought on a showroom floor and then quietly blamed for years. It is chosen for its glass panel, its touch controls and its auto-clean badge, and almost never for the two things that decide whether it works: how much air it actually moves, and where that air is sent afterwards. Indian cooking is the hardest test a chimney faces anywhere in the world. Tempering mustard seeds in hot oil, deep-frying pooris, searing on a high flame and the daily tadka all throw up a mixture of steam, smoke and airborne oil that a European-style hood designed for simmered sauces was never meant to handle.

The result is familiar in thousands of flats. A chimney runs on full speed and still lets a haze drift towards the hall; the wall above the hob turns yellow; the ceiling near the chimney grows a sticky film; and within a year the whole unit hums louder and pulls weaker. In most of these kitchens the machine was never the problem. It was mounted too high, or too low; it was pushed into a recirculating mode with a charcoal filter because no one planned a duct; or the duct it did have ran four metres with three sharp bends to reach a far wall. A chimney is a fan and a path. Both have to be designed.

This article treats the chimney as what it is — a ventilation system, not a decorative hood — and works through the numbers that make one effective in an Indian kitchen: the suction a kitchen of a given size needs, the width that pairs with a two-burner or four-burner hob, the mounting height that balances capture against head clearance, and above all the ducting, which is where most of the performance is won or lost. Prices are given as indicative October 2026 ranges and should be confirmed with a local dealer before budgeting.

From the chulha to the smart hood: a short history

Indian kitchens managed smoke long before chimneys arrived. The traditional chulha was placed against an outer wall or below a roof vent, and the house was planned so that smoke rose and left through a gap in the eaves or a small high window. When kerosene and then LPG stoves moved cooking indoors and upwards onto a counter, that natural escape route was lost, and for decades the only answer was the exhaust fan set into a window or an outside wall. An exhaust fan pulls air out of the room, but it does nothing to capture smoke at the source, so grease still coated the kitchen before the fan could remove it from the air.

The wall-mounted hood chimney reached Indian homes in quantity in the 2000s, first as simple ducted boxes with aluminium mesh filters, then as the glossy glass-and-steel units sold today. The last fifteen years added auto-clean collection bowls, baffle filters borrowed from commercial kitchens, filterless designs, and quieter brushless (BLDC) motors. The hardware has improved enormously. What has not kept pace is the planning around it: the duct, the outlet and the mounting height are still treated as an afterthought on installation day rather than as part of the kitchen drawing.

Fig. 1 — How Indian kitchens handle smoke Traditionalchulha on wallroof / eaves ventnatural escape 1980s–90swindow exhaustfanno capture 2000sducted hoodmesh filtercapture at source 2010sauto-cleanbaffle / filterlesseasier upkeep Now–futureBLDC motorsensors, quietauto speed The machine keeps improving; the weak link is still the duct and the outlet, fixed on installation day rather than drawn into the kitchen plan. A great chimney on a bad duct performs like a cheap one.
Fig. 1 — Kitchen ventilation in India, from chulha to smart hood

What a chimney must do, and how suction is measured

A kitchen chimney has one job: to capture the plume of steam, smoke and oil mist rising off the hob before it spreads into the room, and to move that air away. It does this by drawing air up into a collector, through a filter that traps the oil, and then either out through a duct or, in a ductless unit, through a charcoal filter and back into the room. The capacity to move air is quoted as suction power in cubic metres per hour (m³/hr) — the volume of air the chimney can pull in an hour under test conditions. Indian brands commonly quote figures from about 700 m³/hr at the low end to 1500 m³/hr and beyond.

The honest reading of that number matters. Suction is measured at the fan, not at the hob, so the figure on the box is the best case. Every filter, every metre of duct and every bend eats into it, which is why a generous rating and a short, straight duct belong together. A chimney rated at 1200 m³/hr on a clean, short duct will outperform an 1800 m³/hr unit strangled by a long, kinked one. The useful way to size a chimney is therefore to work out the air the kitchen needs moved, then choose a rating comfortably above it to leave headroom for the duct and for filters that slowly clog.

Fig. 2 — How big a fan does the kitchen need? 3000 length 3000 depth 2700 height Rule of thumb Kitchen volume × 10 to 15 air changes per hour. 3 × 3 × 2.7 m ≈ 24 m³ 24 × 12 ≈ 290 m³/hr of pure room exchange — but Indian cooking needs far more capture at source. Practical minimum: 1000–1200 m³/hr for a 2–3 burner hob; 1200–1500+ for a 4-burner / open kitchen. The air-change sum sets a floor, not the answer. Frying and tempering release oil mist in bursts, so size up — and remember the duct and ageing filters will shave 20–40 per cent off the rated figure in daily use.
Fig. 2 — Sizing suction from kitchen volume and air changes (mm, m³/hr)

A sensible way to size suction

Two rules combine well in Indian kitchens. The first is the air-change rule: multiply the kitchen's volume in cubic metres by ten to fifteen to get a baseline, because a working kitchen wants its air replaced a dozen or more times an hour. The second is a capture allowance for the way Indians cook: deep-frying and tempering release oil mist in sudden bursts that a baseline figure underestimates, so the chimney should be chosen a clear step above the air-change number. In practice a compact closed kitchen with a two or three-burner hob is well served by 1000–1200 m³/hr, while a four-burner hob, a larger kitchen, or an open kitchen joined to the living room wants 1200–1500 m³/hr or more.

Kitchen situationApprox. volumeBaseline air-change needRecommended rated suction
Compact closed kitchen, 2-burner hob18–22 m³≈ 220–330 m³/hr1000–1100 m³/hr
Standard closed kitchen, 3-burner hob22–28 m³≈ 260–420 m³/hr1100–1200 m³/hr
Large closed kitchen, 4-burner hob28–36 m³≈ 340–540 m³/hr1200–1400 m³/hr
Open kitchen joined to living/diningShared volumeHigher — air escapes to the hall1400–1500+ m³/hr, strong capture
Heavy frying / joint-family cookingAnyAdd a marginSize one step above the row that fits

Mounting height: the number most often got wrong

Even a correctly sized chimney fails if it hangs at the wrong height. Too high, and the rising plume spreads and cools before it reaches the collector, so smoke drifts sideways into the room; too low, and the cook's head hits the glass, the heat of a tall flame can damage the unit, and tall vessels do not fit under it. For a gas hob the settled range is 650–750 mm from the burner grate to the underside of the chimney, with 700 mm a safe middle figure for most adults. An induction or electric hob produces a weaker, cooler plume and can be mounted a touch lower, around 550–650 mm, so the capture edge sits closer to the pan.

Fig. 3 — Mounting height over a gas hob (section) flame zone 650–750 gas (550–650 induction) 850–900 counter chimney collector captured plume Too high plume spreads and cools; smoke drifts to the room. Too low head hits glass; flame heat damages the unit. Right capture edge sits in the rising plume before it widens. Measure from the burner grate, not the counter. A 700 mm gap above a 850–900 mm counter puts the collector at roughly 1550–1620 mm — comfortable for most adults and clear of tall pressure cookers.
Fig. 3 — Chimney mounting height above the hob (section, mm)

The height is measured from the burner grate, not from the counter, which is why the same chimney sits at a different absolute height over a gas hob and an induction top. With a counter at 850–900 mm and a 700 mm gap, the collector lands at roughly 1550–1620 mm above the floor — high enough to clear a tall pressure cooker, low enough for a person of average height to see the back burners. In kitchens where the cook is notably tall or short, the height should be adjusted by eye on site; the range exists precisely so it can be tuned to the household.

Ducted or ductless: why ducted wins in Indian homes

Every chimney is sold in two modes. A ducted (or exhaust) chimney captures the oil on its filter and pushes the remaining hot, humid, smelly air out of the building through a pipe. A ductless (or recirculating) chimney adds a charcoal filter that tries to scrub odour from the air and then blows it back into the kitchen. The difference matters enormously for Indian cooking. Ducted mode removes the heat and the steam as well as the smell, which keeps the kitchen cooler and drier; ductless mode returns heat and moisture to the room and relies on a charcoal filter that saturates in a few months and must be replaced to keep working. For a kitchen that fries, tempers and cooks three meals a day, ducted is almost always the right answer.

Ductless mode has its place — a rented flat where the wall cannot be cored, an internal kitchen with no accessible outside wall, or a household that cooks lightly. But it is a compromise, not a convenience, and it should be a deliberate choice made because ducting is genuinely impossible, not a default accepted because no duct was planned. The commonest avoidable mistake in Indian kitchens is buying a capable ducted chimney and then running it in recirculating mode for years because the builder left no outlet and nobody planned one during the fit-out.

AspectDucted (exhaust) chimneyDuctless (recirculating) chimney
Removes smoke & oil mistYes — out of the buildingPartly — recirculates cleaned air
Removes heat & steamYesNo — returns them to the kitchen
Odour controlExcellentFair; fades as charcoal saturates
Running costLow — no charcoal to replaceCharcoal filter replaced every 3–6 months
Needs an outside outletYes — wall core or duct routeNo
Best forAlmost all Indian kitchensRentals / internal kitchens with no wall access

Designing the duct run

The duct is where a good chimney is made or broken, and it is the part most often improvised on installation day. Three things decide how much a duct costs the chimney in lost suction: its diameter, its length and its number of bends. The standard Indian duct is 150 mm (six inch) diameter; narrowing it to save space chokes the airflow and makes the motor work harder and louder. The run should be as short as the kitchen allows — ideally under about three metres — and should reach the nearest outside wall rather than the most convenient-looking one. Every ninety-degree bend behaves like adding roughly a metre of straight duct, so two sharp bends can halve the effective performance of an otherwise strong chimney.

Fig. 4 — Short straight duct vs long bent duct (plan) hob hob outlet outlet short run GOOD one bend, under 3 m, 150 mm pipe BAD 4 bends, long run — suction halved
Fig. 4 — Duct routing: a short straight run against a long, bent one (plan, mm)

Three details finish the job. The outlet should pass through the wall to the outside and be fitted with a cowl or a weather flap that keeps rain, birds and the neighbours' pigeons out while letting air escape; a bare hole invites all three. The duct itself should be rigid or semi-rigid aluminium where possible rather than the thin, concertina-style flexible pipe that sags, tears and collects oil in its folds. And the whole route should be planned at the drawing stage, because the chimney's position, the cabinet that hides the duct and the core-cut through the wall all have to agree. In kitchens with an island hob, the duct must rise into the slab or a bulkhead, which has to be decided before the ceiling is closed.

Filters: baffle, mesh and filterless

The filter is what traps the oil so the fan and the duct stay clean, and three types dominate the Indian market. The aluminium mesh (cassette) filter is a stack of fine layers; it captures oil well but clogs quickly and must be soaked and scrubbed every week or two, or airflow collapses. The baffle filter, borrowed from commercial kitchens, is a set of curved steel plates that force the air to change direction so the oil drops out; it keeps airflow steadier as it fills and needs cleaning less often, perhaps monthly. The filterless or auto-clean chimney has no removable oil filter in the airflow at all: the oil is flung by the blower into a collection bowl that is emptied periodically, and a heater loosens the residue on a cleaning cycle.

Filter typeHow it traps oilCleaningAirflow as it fillsBest for
Mesh / cassetteFine aluminium layersSoak & scrub every 1–2 weeksDrops quickly when cloggedBudget units, light cooking
BaffleCurved plates redirect airWash monthly (often dishwasher-safe)Stays steadierRegular Indian frying and tempering
Filterless / auto-cleanOil flung into a collection bowlEmpty bowl; run auto-clean cycleMost consistentHeavy cooking, low-maintenance households

Width, hob pairing and the cabinet gap

Chimney width should match or slightly exceed the hob width so the collector sits over the whole cooking area. A two or three-burner hob pairs with a 60 cm chimney; a four-burner hob, where the outer burners sit wider apart, is better served by a 90 cm chimney so the corner burners are still under the capture edge. Going wider than the hob is harmless and often helpful; going narrower leaves burners uncovered and smoke escaping at the sides. The kitchen drawing should leave a clear gap of 60 or 90 cm in the wall cabinets for the chimney, with the cabinets on either side built to the same depth so the chimney does not jut awkwardly forward.

HobChimney widthTypical rated suction to pairWall-cabinet gap to leave
2-burner60 cm1000–1100 m³/hr600 mm
3-burner60 cm1100–1200 m³/hr600 mm
4-burner90 cm1200–1400 m³/hr900 mm
Island / wide cooktop90 cm island model1400–1500+ m³/hrDuct route into slab/bulkhead

Costs, and what always sits outside the chimney price

Chimney prices in India span a wide band because the category runs from a basic mesh-filter unit to a wide auto-clean island model. The figures below are indicative October 2026 ranges for the appliance; they exclude ducting and installation, which are quoted separately and are easy to forget. The duct pipe, the bends, the wall core-cut, the cowl and the electrical point together usually add a few thousand rupees, and an island installation that routes a duct into the slab costs more because the work is structural rather than cosmetic. As with the rest of a modular kitchen, the chimney is an appliance line item and does not come inside the per-square-foot cabinetry rate.

Chimney typeIndicative price (Oct 2026)Suited to
60 cm, mesh/baffle, manual clean₹8,000–12,000Compact kitchens, 2–3 burner hobs, light use
60 cm, auto-clean₹12,000–18,000Regular cooking, easier upkeep
90 cm, baffle filter₹14,000–22,0004-burner Indian cooking on a budget
90 cm, auto-clean / filterless (often BLDC)₹18,000–35,000Heavy cooking, quieter open kitchens
Island chimney, 90 cm₹30,000–55,000Island hobs; duct routed through slab/bulkhead
Ducting + installation extras₹3,000–8,000Duct, bends, wall core-cut, cowl, electric point

A reasonable budget for a typical closed Indian kitchen, therefore, is an auto-clean 60 or 90 cm unit at ₹12,000–22,000 plus ₹3,000–8,000 for ducting and installation. Spending more on the appliance while skimping on the duct is the wrong trade: a mid-range chimney on a short, straight, well-sealed 150 mm duct will keep a kitchen cleaner than a premium one strangled by a long, bent, leaky pipe.

Where kitchen chimneys are going

The direction of travel is quieter, smarter and more efficient. Brushless (BLDC) motors are spreading down from premium to mid-range models, cutting both noise and power draw for the same airflow. Auto-sensing chimneys that detect heat or smoke and raise their own speed, gesture and app controls, and motion-activated start are becoming common. None of these features changes the fundamentals this article is built on: a chimney still has to move enough air, hang at the right height, and send its air out through a short, straight duct. A smart chimney on a bad duct is still a bad installation. The sensible buyer treats the electronics as a convenience layer on top of a system that was sized and ducted correctly first.

Rules for specifying a kitchen chimney

  • Size suction from the kitchen volume and cooking style: 1000–1200 m³/hr for a 2–3 burner hob, 1200–1500+ for a 4-burner or open kitchen.
  • Match chimney width to the hob — 60 cm for 2–3 burners, 90 cm for a 4-burner — and never go narrower than the hob.
  • Choose ducted mode unless an outside outlet is genuinely impossible; treat ductless as a compromise, not a default.
  • Mount the collector 650–750 mm above a gas burner grate (550–650 mm over induction), and tune it to the cook's height on site.
  • Keep the duct 150 mm in diameter, under about three metres, and with as few 90° bends as the layout allows.
  • Route the duct to the nearest outside wall and fit a cowl or weather flap; avoid thin flexible concertina pipe where rigid duct will fit.
  • Plan the chimney position, the duct route and the wall core-cut on the kitchen drawing, not on installation day.
  • Budget ducting and installation as a separate line, and keep the chimney outside the per-square-foot cabinetry rate.

Frequently asked questions

How much suction power does a chimney need in India?

For a closed kitchen with a two or three-burner hob, about 1000–1200 m³/hr is comfortable; for a four-burner hob or an open kitchen that shares air with the living room, aim for 1200–1500 m³/hr or more. Because the duct and ageing filters shave twenty to forty per cent off the rated figure in daily use, it is sensible to choose a rating a clear step above the bare air-change calculation.

Should the chimney be 60 cm or 90 cm?

Match it to the hob. A two or three-burner hob is covered by a 60 cm chimney; a four-burner hob spreads its burners wider and is better served by a 90 cm unit so the corner burners stay under the capture edge. A chimney wider than the hob is fine; one narrower than the hob leaves smoke escaping at the sides.

Is a ductless (filterless auto-clean) chimney good enough?

Filterless and ductless are two different things. Filterless (auto-clean) describes how the oil is collected and is an excellent, low-maintenance choice. Ductless describes recirculating the cleaned air back into the room; it removes some odour but returns heat and steam and relies on a charcoal filter that saturates in a few months. For regular Indian cooking a ducted chimney — filterless or not — is the better system wherever an outside outlet is possible.

At what height should a chimney be installed above the hob?

Measure from the burner grate, not the counter. For a gas hob the capture works best at 650–750 mm, with 700 mm a safe middle figure; for an induction or electric hob the plume is weaker, so 550–650 mm brings the collector closer to the pan. Too high and smoke drifts into the room; too low and the cook's head meets the glass.

How long can the chimney duct be?

As short as the layout allows — ideally under about three metres — in 150 mm pipe, routed to the nearest outside wall. Each ninety-degree bend acts like adding roughly a metre of straight duct, so keep bends to a minimum; one is ideal, two is a practical maximum before performance suffers noticeably.

Sources & standards

  1. National Building Code of India 2016, Part 8 (Building Services) and Part 3 (ventilation of habitable spaces and kitchens)
  2. Bureau of Indian Standards — IS 374 and related standards for domestic electrical appliances; appliance safety and labelling
  3. Bureau of Energy Efficiency (BEE) — star-rating and energy-efficiency guidance for domestic appliances and motors
  4. Neufert, Architects' Data — kitchen ergonomics, extraction hood positioning and clearances
  5. Time-Saver Standards for Building Types / Interior Design — kitchen ventilation and appliance planning
  6. Manufacturer specification sheets (generic Indian market ranges) — suction ratings, duct diameters and mounting heights
  7. Price ranges: indicative October 2026 estimates — confirm locally before budgeting
Discuss your project