The stilt floor is one of the most common and least understood parts of an Indian apartment building. It is the open ground level — columns, a slab overhead, no walls — that is given over to parking, while the flats sit on pilotis above it. For buyers it is where the car lives; for the building it is a structural and regulatory decision made long before the first flat is sold. When it is planned well, a stilt gives covered parking, a cooler, shaded, flood-safer ground level and a sheltered place for the lobby, the lift and services. When it is planned badly, it gives cars that cannot turn, bays too tight to open a door, beams that scrape the roof of an SUV, and a ramp so steep that cars ground on it.
Almost every stilt failure is dimensional and almost every dimension is fixed by the column grid, which is set when the structure is designed and cannot be changed afterwards. The number of cars a stilt holds, whether a door can be opened, whether a car can reverse out without a ten-point turn, and whether a tall vehicle clears the beams — all of it is decided by the spacing of the columns and the clear height under the lowest obstruction. A stilt is therefore an architecture-and-planning problem, not a finishing one: it must be got right on the structural grid, in coordination with the local building rules, long before anyone thinks about the floor tiles or the paint. This article sets out the rules, the bay and aisle dimensions, the clear height, the ramp slopes, the column grids and the costs that make a stilt work.
It is written for people buying or building in an apartment and for designers laying out a ground floor. The dimensions are typical Indian planning values and reflect common development-control provisions; the exact figures — bay sizes, clear height, the counting of stilt area against FSI, and how many car spaces each flat must have — are set by the local building bye-laws and development-control regulations, which differ by city and state and are the version any plan is actually approved against. The term pilotis, from modern architecture, describes the same idea: a building lifted on columns over an open ground level.
What a stilt floor is
A stilt floor is an open or largely open storey at ground level, carried on columns, over which the building rises. Its defining features are that it is unenclosed — no external walls, or only partial ones — and that it is normally used for parking, services, the entrance lobby, the lift and stair cores, and sometimes a watchman's room or a utility. Because it is open and dedicated to parking and services, many development-control regulations treat a stilt differently from a habitable floor: the stilt is often not counted, or only partly counted, against the permitted floor space index (FSI/FAR), and it is often not counted as a storey for height limits, which is precisely why developers use it. A stilt is not a basement, which is below ground and needs ramps down, waterproofing and ventilation; nor a podium, which is a raised deck of parking with building above; it is an open ground level raised just enough, or kept at grade, for parking.
The attractions of the stilt are practical as well as regulatory. Covered parking keeps cars out of the sun and rain; raising the living floors above the open ground level helps in areas prone to waterlogging and gives the flats more privacy and breeze; and the open ground level is a cooler, shaded, flexible space that can also hold a community area, a children's play spot or a sitting-out area beyond the parking. The trade-off is that the whole ground level's usefulness depends on it being dimensioned correctly for vehicles, because a stilt that cannot actually park and manoeuvre the number of cars the building needs is a planning failure that no finish can rescue.
Car bay and aisle dimensions
The basic unit of a stilt is the car bay, and the figure to anchor everything to is a space of about 2.5 × 5.0 m (2500 × 5000 mm) for a standard car — wide enough to open a door and long enough for the car plus a little clearance. Many bye-laws specify an equivalent-car-space area in square metres, but the 2.5 × 5.0 m bay is the practical shape most layouts use. A compact-car space can be a little smaller, but designing to the smaller figure is a false economy because cars have grown: an SUV or a large sedan needs the full 2.5 m width to open doors without hitting the next car, and a tight bay is the commonest complaint in built stilts. Where two cars park side by side for one flat, allow about 5.0 to 5.5 m of combined width.
A bay is useless without the room to drive into and out of it, and the drive aisle is where stilts most often jam. For cars to reverse out of a perpendicular (90-degree) bay and turn into the aisle in one or two movements, the aisle needs to be wide — commonly about 5.5 to 6.0 m for 90-degree parking, less for angled parking, and about 3.0 to 3.6 m where it is a one-way drive with no parking manoeuvre. Parallel parking along an aisle needs a longer bay (about 5.5 to 6.0 m) but a narrower aisle. The relationship between bay angle and aisle width is the heart of parking layout: steeper angles pack more cars per metre of wall but need wider aisles to turn into; 90-degree bays are space-efficient only if the aisle is generous enough to use them. The table below gives the working figures.
| Element | Dimension | Note |
|---|---|---|
| Standard car bay | 2.5 × 5.0 m (2500 × 5000 mm) | The anchor figure; opens doors and parks a large car |
| Two cars side by side (one flat) | ≈ 5.0–5.5 m combined width | Door-opening clearance between them |
| Aisle, 90-degree parking | 5.5–6.0 m | Width to reverse out and turn in one or two moves |
| Aisle, angled (30–60°) parking | 3.0–5.0 m | Narrower aisle; fewer cars per metre of wall |
| Aisle, one-way drive, no parking | 3.0–3.6 m | Pure circulation lane |
| Parallel bay (along an aisle) | ≈ 2.5 × 5.5–6.0 m | Longer bay, narrower aisle |
Clear height: the SUV problem
Height is where stilts quietly fail, and the culprit is almost always a beam or a service pipe, not the slab. The clear height of a stilt — the usable headroom for a vehicle — is measured to the lowest obstruction, which is typically the underside of a down-stand beam, a duct, a sprinkler line or a sewer pipe running below the slab, not the slab soffit itself. A common minimum clear height for parking is about 2.4 m under the lowest beam or service, and many regulations and good layouts aim higher, around 2.5 m or more, because modern SUVs, vans and vehicles with roof carriers are tall. A stilt that measures 2.7 m to the slab but 2.2 m under a crossing beam will scrape tall vehicles exactly where that beam runs, and the owners will discover it only after moving in.
Designing the clear height right means coordinating the structure and the services together. The beam layout should run so that the deepest beams fall over the aisles or the bay-dividing lines rather than across the middle of a bay and the path a car follows; services should be routed and the slab zone planned so that the lowest service still leaves the target clear height along every driving and parking path. Signage and a physical height bar at the entrance warn drivers of the real limit. Because the clear height is set by the structural depth and the services, it is fixed at design stage and is extremely expensive to recover afterwards — raising a slab is not a renovation. The clear height is one of the first numbers to confirm when assessing a stilt, and it should be checked under the beams, not in the open middle of the floor.
| Clearance | Typical figure | Measured to | Why |
|---|---|---|---|
| Clear height for parking | ≥ 2.4 m (aim 2.5 m+) | Underside of the lowest beam or service | Tall SUVs and vans must clear every path |
| Height at the entrance | Height bar at the clear height | Physical limiter and sign | Warns tall vehicles before they enter |
| Gap between parked cars | 500–600 mm | Side of car to side of car | Room to open doors without dents |
| Gap, car to column | 300 mm or more | Side of car to column face | Avoids scraping on the columns |
| Pedestrian walkway at edge | About 1.0–1.2 m where provided | Marked lane clear of bays | Safe route past parked cars |
Ramps: getting cars up or down
Wherever the parking level is not exactly at the road level — a stilt raised a little above grade, or a basement below it — a ramp connects them, and its slope is critical. A ramp that is too steep grounds the car's front or rear, is dangerous in the wet, and is hard for low vehicles; a ramp that is too gentle eats floor area. Common practice keeps a car ramp no steeper than about 1:8 (one vertical in eight horizontal) for short ramps, and gentler, around 1:10 or flatter, for longer ones and in regulations that require it. Steeper transitions at the top and bottom of a ramp need a shallower transition length so the car does not ground where the slope changes. The ramp width follows the aisle logic — about 3.0 m for one-way and 5.5 to 6.0 m or a divided ramp for two-way.
A small rise needs a surprising length of ramp. At 1:10, lifting a car 1.0 m takes 10 m of ramp run; at 1:8, it takes 8 m, plus transitions. This is why a stilt is usually kept close to road level, with at most a shallow ramp or a kerb-height step, and why a true basement, which must drop a full storey below ground, needs a long ramp, waterproofing, drainage with a sump pump, and mechanical ventilation — a far bigger undertaking than a stilt. The ramp surface must be non-slip, the slope signed, and a gradient transition provided at both ends. Where a ramp turns, it must be wide enough on the inside of the bend for a car to track around without mounting the kerb.
| Ramp use | Max slope (typical) | Run for 1 m rise | Width |
|---|---|---|---|
| Short car ramp | ≈ 1:8 | ≈ 8 m plus transitions | 3.0 m one-way; 5.5–6.0 m two-way |
| Long car ramp / regulated | ≈ 1:10 or flatter | ≈ 10 m plus transitions | As above; divide wide ramps |
| Transition at ramp ends | About half the ramp slope | Short length each end | Full ramp width |
| Pedestrian ramp (accessibility) | 1:12 or gentler | 12 m for 1 m, with landings | Handrails and landings required |
The column grid: where every stilt is decided
The dimensions above only come together through the column grid — the regular spacing of the structural columns that carry the building. Because a car bay is about 2.5 m wide, columns are usually spaced so that a clear run of two or three bays fits between them; a very common approach places columns about 5.0 m apart in one direction (two 2.5 m bays) and across an aisle in the other, so cars park between columns rather than against them. A column landing in the middle of a bay, or spaced so a car straddles two bays awkwardly, wastes spaces and is impossible to fix once cast. The grid also has to leave the lift and stair cores, the entrance lobby, the services and any ramp their space, all woven into the same column lines.
This is why a stilt is an architecture-and-planning decision taken with the structural engineer at the very start, not a layout drawn on the finished floor. The designer works forward and backward at once: the number of flats sets the number of car spaces the bye-law demands, those spaces plus their aisles set the floor area and the grid, and the grid must also carry the building efficiently above. A good stilt layout is one where the columns fall on bay lines, every demanded car space is usable, the aisles let cars turn, the clear height holds under every beam along the driving paths, and the cores and services fit without stealing a bay. Getting this grid right is the whole game; the finishes come much later and matter far less.
Rules, finishes and costs
The rules around a stilt are set locally and matter more than any national figure. Development-control regulations and municipal bye-laws decide whether the stilt counts against FSI (it is often exempt or partly exempt where used for parking and services), whether it counts as a storey for the height limit, the minimum clear height, how many equivalent car spaces each flat must provide, and how the parking and circulation must be laid out. These vary by city and state — Gujarat's development-control regulations, for example, set their own parking and stilt provisions — and they are what a plan is approved against, so they must be read first. Enclosing a stilt with walls to make rooms is a common and serious violation, because it converts exempt parking area into unauthorised floor space and removes the parking the building was approved with.
Compared with the structure, the finishes are modest. The floor takes the heaviest wear in the building — turning tyres, dripping engines, point loads — so it should be a hard, non-slip surface: heavy-duty full-body vitrified tiles (structured, high slip-rating), a trowel-finished or trimix concrete floor, or an epoxy or hardener-coated concrete, typically in the range of about ₹60 to 160 per sq ft depending on the choice. The columns need corner guards or rubber bumpers where cars pass close; the floor should fall gently to a drain so wash water and rain run off; and the stilt needs good lighting and ventilation because it is a semi-enclosed space where vehicles run. Line-marking the bays, numbering them, and a height bar at the entrance complete a usable stilt. Indicative October 2026 costs for these finishes are modest set against the civil cost of the structure itself.
| Item | Choice | Indicative cost (2026) | Note |
|---|---|---|---|
| Stilt floor finish | Heavy-duty full-body vitrified tile | ≈ ₹85–160 per sq ft laid | Structured, high slip-rating (R11–R12) |
| Stilt floor finish | Trimix / trowelled or coated concrete | ≈ ₹60–120 per sq ft | Economical, durable, non-slip |
| Column guards | Rubber bumpers / corner protectors | ₹500–3,000 per column | Protect columns from car contact |
| Bay marking and numbering | Paint / thermoplastic lines | Project-specific | Define and number every space |
| EV charging point (per bay) | Home / AC charger with supply | ₹3,500–60,000 per point | Plan supply and metering from the start |
| Height bar and signage | Entrance height limiter and signs | Project-specific | Warns tall vehicles of the clear height |
The stilt tomorrow: EVs, mechanical parking and shared space
The stilt is being asked to do more as cities grow denser and cars change. The clearest shift is electric-vehicle charging: new stilts increasingly need a charging point, or at least the wiring and the metered supply for one, at a meaningful share of the bays, which means planning the electrical capacity, cable routes and metering into the ground floor from the start rather than retrofitting it awkwardly later. Where land is scarce, mechanical and puzzle parking systems stack cars on powered platforms to fit more vehicles into the same stilt or basement footprint, trading simplicity for density and needing more clear height and maintenance. And as the shortage of parking bites, the open stilt is increasingly valued as flexible community space — a shaded area for gatherings, children's play or sitting out — beyond the rows of cars.
What does not change is that the stilt is set on the structural grid and the local rules, once, at the design stage. Whatever is parked there and however it is charged, the bays still need about 2.5 × 5.0 m each, the aisles still need the width to turn cars, the clear height still has to hold about 2.4 m or more under every beam along the driving path, the ramps still cannot be too steep, and the columns still have to fall on bay lines. A stilt is judged by plain questions: Does it hold the car spaces the building was approved for? Can a large car park and reverse out of every one of them? Does a tall vehicle clear the beams? And has it been kept open as approved, not quietly walled in? Aaditya Interior's planning advice is simple — fix the grid, the clear height and the ramp with the structural engineer and the bye-law in hand before anything else, because a stilt gone wrong on the grid cannot be put right afterwards.
Rules for planning a stilt floor
- Read the local development-control regulations and bye-laws first — they set the FSI treatment, the car-space count, the clear height and the layout the plan is approved against.
- Anchor every bay to about 2.5 × 5.0 m, and do not shrink it — modern cars need the full width to open doors.
- Match the aisle to the parking angle: about 5.5–6.0 m for 90-degree bays, narrower for angled or one-way drives.
- Fix the column grid so columns fall on bay lines (about 5.0 m, two bays) and no column lands in the middle of a space.
- Confirm the clear height to the underside of the lowest beam or service along every driving and parking path, aiming for about 2.4 m or more.
- Keep ramps no steeper than about 1:8 short or 1:10 long, with gentler transitions at both ends so cars do not ground.
- Weave the lift and stair core, the lobby, services and any ramp into the same grid without stealing a demanded car space.
- Finish the floor in a hard, non-slip surface that falls to a drain, guard the columns, and fit a height bar and bay marking.
- Never enclose the stilt with walls to make rooms — it is an approval violation and removes the parking the building depends on.
Frequently asked questions
What is stilt parking?
Stilt parking is parking on an open, columned ground level with the building raised on pilotis above it. The ground floor has no external walls, or only partial ones, and is given over to cars, the entrance lobby, the lift and stair cores and services. Because it is open and used for parking, many development-control regulations do not count the stilt, or count it only partly, against the permitted FSI and the storey height limit, which is why developers favour it.
What is the minimum size of a stilt car parking space?
The practical anchor is a bay of about 2.5 × 5.0 m (2500 × 5000 mm), wide enough to open doors and long enough for a large car. Many bye-laws state an equivalent-car-space area in square metres instead, but the 2.5 × 5.0 m bay is the shape most layouts use. Designing to a smaller compact-car figure is a false economy because cars have grown; confirm the exact requirement with the local regulations.
What clear height does a stilt need?
A common minimum clear height for parking is about 2.4 m, and many layouts aim for 2.5 m or more because modern SUVs and vans are tall. Crucially, clear height is measured to the underside of the lowest obstruction — a down-stand beam, a duct or a pipe — along the car's path, not to the open slab soffit. A stilt that looks tall in the open middle can still scrape vehicles under a crossing beam, so always check the height under the beams.
How steep can a parking ramp be?
Car ramps are commonly kept no steeper than about 1:8 (one in eight) for short ramps and around 1:10 or gentler for longer ones and where regulations require it, with shallower transitions at the top and bottom so the car does not ground where the slope changes. A 1 m rise needs about 8 m of ramp at 1:8 or 10 m at 1:10, plus transitions, which is why stilts are usually kept close to road level.
Can stilt parking be converted into a room?
No — enclosing a stilt with walls to make a room or shop is a serious violation in most places. The stilt is approved as open parking and is often exempt from FSI on that basis, so walling it in both creates unauthorised floor space and removes the parking the building was sanctioned with, exposing owners to demolition notices and penalties. The open stilt can be used flexibly for community space, but it must stay open as approved.
Sources & standards
- National Building Code of India 2016, Part 3 (Development Control Rules and General Building Requirements) — parking provisions, stilt and circulation requirements
- National Building Code of India 2016, Part 4 (Fire and Life Safety) — ventilation and access for parking areas
- Local development-control regulations and municipal building bye-laws (for example Gujarat's Comprehensive General Development Control Regulations) — FSI treatment of stilts, car-space requirements and clear height
- Neufert, Architects' Data — car parking bay, aisle, ramp and turning dimensions
- Time-Saver Standards for Building Types and for Site Planning — parking layout and ramp gradients
- Price ranges: indicative October 2026 estimates — confirm locally before budgeting



