← All articles

Heights & Depths · 08 Nov 2026 · 20 min read

Wardrobe Internal Dimensions: Shelves, Hanging, Drawers and Sizes

Wardrobe Internal Dimensions: Shelves, Hanging, Drawers and Sizes — cover

A wardrobe is judged from the inside. The shutters, the handles and the finish are what a showroom sells, but what a family lives with every morning is the space behind them: whether a saree or a sherwani hangs without creasing, whether folded shirts sit in reachable stacks, whether there is a drawer for the small things that otherwise end up in a heap. Most wardrobes in Indian homes disappoint not because they are badly built but because their insides are planned carelessly — one long rod across the whole unit, a few shelves at random heights, and a lot of wasted air at the top and bottom.

The waste is usually invisible until it is measured. A single hanging rod across a 2100 mm tall wardrobe leaves more than a metre of dead space below the shirts, where two drawers or a shelf stack should be. Shelves spaced 500 mm apart look generous but hold the same stack of folded clothes as a 350 mm shelf, with the extra height doing nothing. A rod set too low creases trousers against the floor of the unit; a rod set too deep makes hangers foul the shutter. Each of these is a dimension problem, and each is fixed with a standard number rather than a guess.

This article sets out the internal dimensions that make a wardrobe work: the overall depth and height, the heights and clear lengths for full-length, short and double hanging, the spacing of shelves for folded clothes, the sizes of drawers, and the module widths that let a wardrobe be built efficiently from standard sheets. It treats the wardrobe as a set of zones — hang, fold, drawer and accessory — and gives the sizes for each, so the inside can be planned on paper before a single board is cut. Prices are indicative October 2026 ranges, to be confirmed locally.

From the almirah to the fitted wardrobe: a short history

Indian clothes storage began as free-standing furniture: the wooden almirah and the steel Godrej-style cupboard, both bought as objects and placed against a wall. These were sized by the factory, not the room, so they rarely used the full height and left gaps at the sides. The built-in or fitted wardrobe — a carcass made to measure, floor to ceiling, wall to wall — arrived with modern interior fitouts and changed the economics: it uses every millimetre of the opening, hides the gaps, and lets the inside be divided exactly to the family's clothes. The walk-in wardrobe, a small room lined with open and shuttered storage, is the premium end of the same idea.

What travelled unchanged from the almirah to the fitted wardrobe is the human dimension. Clothes are the same size whatever holds them: a shirt on a hanger needs the same width, a saree the same hanging length, a folded stack the same shelf gap. The fitted wardrobe simply lets those fixed garment dimensions, rather than a factory's catalogue, decide the internal layout. That is why the numbers in this article are stable — they come from the clothes and the body, not from a product, and they hold whether the wardrobe is hinged, sliding or a walk-in.

Depth and height: the shell the inside lives in

Every internal dimension starts from the depth. A clothes hanger is about 440–450 mm wide across the shoulders, and it must hang square to the back without the garment rubbing the shutter. That sets the standard internal depth at about 550–600 mm, with 600 mm the comfortable number most designers work to. A hinged wardrobe can use the full internal depth for storage; a sliding wardrobe loses about 80–100 mm to the track and overlapping shutters, so its carcass is built a little deeper — around 650–680 mm overall — to keep 550–600 mm usable inside. Height runs to the ceiling, typically 2100–2400 mm of usable storage with a loft above for suitcases and seasonal bedding.

Fig. 1 — Wardrobe interior, 1800 mm wide × 2100 mm storage (mm) full-length hang double hang shelves floor to rod 1700 short hang 1000 drawers 150–300 lower rod 1000 Divide the height into zones: full-length hang, double hang, folded-shelf stacks and a drawer bank. A loft above 2100 mm takes suitcases and seasonal bedding; keep daily clothes within reach.
Fig. 1 — Wardrobe internal elevation: hang, shelf and drawer zones (mm)
DimensionStandard valueWhy
Internal depth (hinged)550–600 mmA hanger is ~450 mm wide and must hang square
Carcass depth (sliding)650–680 mm overallTrack and overlapping shutters eat 80–100 mm
Usable storage height2100–2400 mmDaily clothes within reach; loft above
Loft / top box height400–600 mmSuitcases and seasonal bedding
Shutter / module width450–600 mm per shutterHinged shutters stay flat and do not sag
Plinth / skirting recess80–100 mmKeeps the carcass off a wet-mopped floor

These shell dimensions are worth fixing before anything else, because every internal zone is measured down from the top and in from the front. A carcass that is too shallow crushes hanging clothes against the shutter; one that is too tall without a loft wastes the reach above the head; one with no plinth lets a mopped floor wet the base board. Getting the shell right first means the hanging, folding and drawer zones can be planned as a simple division of a known height and depth, rather than being squeezed in afterwards.

Hanging: full-length, short and double

Hanging is the heart of the wardrobe, and it comes in three types sized by what hangs in them. Full-length or long hanging is for sarees, gowns, kurtas, coats and dresses; the rod sits about 1700 mm from the floor, leaving roughly 1400–1600 mm of clear drop below so a long garment does not pool on the base. Short or single hanging is for shirts, folded trousers and jackets; it needs about 1000–1100 mm of clear drop, so its rod sits around 1050 mm above a shelf or drawer bank. Double hanging stacks two short rods in the height of one long one — an upper rod near 1950 mm and a lower near 1000 mm — doubling shirt and trouser capacity where no long garments need to hang.

Fig. 2 — Hanging rod heights at one scale (mm) Full-length rod 1700, drop 1500 Short hang rod 1050, drop 1000 Double hang 1950 + 1000 1700 1050 1950 Reserve one full-length section per person for sarees, gowns and long kurtas; double-hang the rest.
Fig. 2 — Hanging rod heights: full, short and double (section, mm)
GarmentHanging length neededSection type
Shirts, blouses800–900 mmShort / double hang
Trousers (on a hanger)1000–1150 mmShort hang
Kurtas, long shirts1100–1300 mmShort or full-length hang
Dresses, suits, sherwani1250–1450 mmFull-length hang
Sarees, gowns, long coats1500–1600 mmFull-length hang
Children's clothes700–900 mmShort / double hang (lower)

Two practical rules go with these numbers. First, the rod is set back about 60 mm from the front of the carcass and a hanger projects forward, so a hinged shutter needs a small clearance and a sliding shutter must not foul the hanger ends. Second, the rod must not sag: a steel rod of about 19–25 mm diameter needs a centre support or an intermediate bracket on any span over roughly 900 mm, or a heavy row of winter coats will bow it. A pull-down wardrobe lift can bring a high rod down to hand height in a tall unit, but it costs more and reduces the clear hanging length, so it is used where the ceiling is high rather than as a default.

Shelves, drawers and accessories

Not everything hangs. Folded clothes — t-shirts, jeans, towels, bedsheets — live on shelves, and the key number is the gap between them. A stack of folded shirts is about 250–300 mm tall, so shelves spaced 300–400 mm hold a comfortable stack with room to lift the top items out; closer than 300 mm and the stack is cramped, wider than 400 mm and the height is wasted or the stack topples. Adjustable shelves on pins are worth the small extra cost, because a family's mix of hanging and folding changes over the years. Drawers handle the small and the private — innerwear, socks, documents, jewellery — and are sized by what they hold rather than by a single standard.

Fig. 3 — Folded-clothes shelves and drawer bank (mm) gap 300–400 150 300 folded shelves drawer bank Shallow drawers (150 mm) for innerwear and socks; deeper drawers (250–300 mm) for jeans and towels.
Fig. 3 — Shelf spacing and drawer sizes (section, mm)
Internal elementSizeHolds
Folded-clothes shelf gap300–400 mmStacks of shirts, t-shirts, jeans
Shelf depth500–550 mmWithin the 600 mm carcass, leaving a finger gap
Shallow drawer (internal)100–150 mm highInnerwear, socks, ties, handkerchiefs
Medium drawer180–220 mm highFolded t-shirts, nightwear
Deep drawer250–300 mm highJeans, towels, bulky knitwear
Jewellery / accessory tray40–70 mm highLined insert tray inside a drawer

Module widths and how a wardrobe is built

A wardrobe is built from sheet material, so the sheet size quietly shapes the design just as it does a jaali or a kitchen. Carcass boards come in 2440 × 1220 mm sheets in 18 mm for the body and 6–8 mm for the back, so internal compartments are planned to cut from these with least waste. A single hinged shutter is kept to about 450–600 mm wide so it stays flat and the hinges do not sag over the years; wider openings use a pair of shutters or a sliding system. A sliding wardrobe typically uses two or three shutters of 900–1200 mm each, overlapping on the track, which is why it loses depth but suits a long wall where swinging shutters would block the room.

TypeShutter / moduleDepthBest where
Hinged wardrobe450–600 mm per shutter550–600 mmMost bedrooms; full depth usable
Sliding wardrobe900–1200 mm per shutter650–680 mmLong walls, tight rooms; no swing space
Openable + loft450–600 mm + loft above550–600 mmStandard full-height built-in
Walk-in wardrobeOpen bays 600–1000 mm550–650 mm per sideA dedicated dressing room

The choice between a hinged and a sliding wardrobe is really a choice about the room, not about the clothes inside. A hinged wardrobe uses the full internal depth and costs less, but each shutter needs swing space in front — roughly the width of the shutter must stay clear so the door can open fully. In a narrow bedroom where the bed sits close to the wardrobe, that swing space may not exist, and a shutter that can only half-open makes the wardrobe awkward to use every day. A sliding wardrobe needs no swing space at all, which is why it suits tight rooms and long walls, but it is built deeper to carry the track and the overlapping shutters, and only ever opens half of its width at once.

Fig. 4 — Hinged vs sliding wardrobe (plan, mm) 600 deep 680 overall swing 600 hinged sliding no door swing Hinged uses full depth but needs swing space in front; sliding needs none but loses depth to the track.
Fig. 4 — Hinged versus sliding wardrobe (plan, mm)

Across these types the internal numbers do not change — depth, rod heights and shelf gaps stay the same whether the door swings or slides. What changes is how the space is reached and how much the doors cost. Sliding systems and soft-close hinges and drawer runners are where a wardrobe's price and feel are decided; the carcass and the layout decide whether it is pleasant to use every day. Aaditya Interior plans the inside first — hanging, folding, drawers and accessories mapped to the family's actual clothes — and lets the shutter type follow the room, rather than choosing a handsome shutter and squeezing the clothes in behind it.

Materials, hardware and cost

Wardrobe carcasses are normally built in BWR plywood or HDHMR for stability, with shutters finished in laminate, membrane, acrylic or PU depending on budget and look, exactly as covered in the board and finish guides. Hardware is where daily quality lives: soft-close hinges and telescopic drawer channels, a sturdy anodised or steel rod with proper brackets, and good handles or profile shutters. Costs below are indicative October 2026 ranges for a made-to-measure fitted wardrobe, measured per square foot of front elevation, material and labour, excluding GST, and vary with finish, hardware grade, city and the amount of internal accessorising.

Finish / typeIndicative cost (per sq ft of elevation)Notes
Laminate hinged wardrobe₹1,200–2,200BWR/HDHMR carcass, laminate shutters, basic hardware
Membrane / foil shutter₹1,500–2,500Routed and moulded shutter looks on a budget
Acrylic-shutter wardrobe₹2,200–3,500Mirror-gloss fronts; premium over laminate
PU-painted wardrobe₹2,500–4,000Seamless painted shutters; highest board finish
Sliding wardrobe (system)₹1,800–3,500Track, rollers and overlapping shutters add cost
Internal accessories (extra)₹5,000–40,000 per wardrobePull-outs, trays, lift rods, soft-close upgrades

Where wardrobe design is going

Wardrobes are moving towards modularity and smarter interiors. Factory-made modular carcasses, cut on computer-controlled machines and assembled on site, are replacing fully site-built units in many cities, giving tighter tolerances and quicker installation while keeping the same internal dimensions. Interiors are being accessorised more — pull-out trouser racks, valet rods, lift-down rails, lit interiors on door sensors, and dedicated trays — turning the wardrobe from a box of rods and shelves into a fitted dressing system. None of this changes the garment-driven numbers; it changes how neatly and how expensively they are delivered. The constant remains the body and the clothes, and a well-dimensioned simple wardrobe will always beat a poorly planned expensive one.

Rules for planning a wardrobe interior

  • Start from 600 mm internal depth for hinged wardrobes; build sliding units to 650–680 mm so 600 mm stays usable.
  • Set a full-length rod about 1700 mm up with 1400–1600 mm clear below for sarees, gowns and long kurtas.
  • Set short-hang rods for 1000–1100 mm of drop, and double-hang shirts and trousers at roughly 1950 and 1000 mm.
  • Give at least one full-length hanging section per person, and double-hang the rest to gain capacity.
  • Space folded-clothes shelves 300–400 mm apart; make shelves adjustable so the mix can change.
  • Size drawers by use: 100–150 mm for innerwear, 180–220 mm for t-shirts, 250–300 mm for jeans and towels.
  • Keep hinged shutters 450–600 mm wide so they stay flat, and support any hanging rod spanning over 900 mm.
  • Plan the inside to the family's actual clothes before choosing shutter type, finish and hardware.

Frequently asked questions

What is the standard depth of a wardrobe?

About 600 mm internally for a hinged wardrobe, because a clothes hanger is roughly 450 mm wide and must hang square to the back without the garment rubbing the shutter. A sliding wardrobe is built a little deeper — around 650–680 mm overall — because the track and overlapping shutters take up 80–100 mm, leaving about 550–600 mm usable inside. Going shallower than 550 mm starts to crease hanging clothes against the shutter.

At what height should a wardrobe hanging rod be?

For full-length hanging — sarees, gowns, long kurtas and coats — the rod sits about 1700 mm from the floor, leaving roughly 1400–1600 mm of clear drop below. For short hanging of shirts and folded trousers, the rod needs about 1000–1100 mm of drop, so it sits around 1050 mm above a shelf or drawer. Double hanging places two short rods one above the other, near 1950 mm and 1000 mm.

How much space between wardrobe shelves?

Space folded-clothes shelves about 300–400 mm apart. A stack of folded shirts is roughly 250–300 mm tall, so this gap holds a comfortable stack with room to lift the top items out. Closer than 300 mm cramps the stack; wider than 400 mm wastes height or lets the pile topple. Adjustable shelves on pins let the spacing change as the clothes mix changes.

Hinged or sliding wardrobe — which is better?

Hinged wardrobes use the full internal depth, cost less, and suit most bedrooms, but the shutters need swing space in front. Sliding wardrobes need no swing space, so they suit long walls and tight rooms, but they lose some depth to the track, cost more, and only ever open half the wardrobe at once. The internal dimensions — rods, shelves, drawers — are the same for both; the choice is about the room and the budget.

How wide should one wardrobe shutter be?

A single hinged shutter is best kept to about 450–600 mm wide, so it stays flat and the hinges do not sag over years of use. Wider openings use a pair of shutters meeting in the middle, or a sliding system where each panel runs 900–1200 mm. The internal compartments behind are planned to cut efficiently from 2440 × 1220 mm boards.

Sources & standards

  1. Ernst Neufert, Architects' Data — anthropometric and garment dimensions for wardrobes and hanging
  2. Time-Saver Standards for Interior Design and Space Planning — clothes storage and dressing-room layouts
  3. Bureau of Indian Standards — IS 303 (plywood for general purposes) and IS 710 (marine plywood) for carcass boards
  4. National Building Code of India 2016, Part 3 (Development Control Rules and General Building Requirements) for room and storage planning
  5. Manufacturer standard ranges for wardrobe hardware — soft-close hinges, telescopic drawer channels and hanging rods (generic)
  6. Price ranges: indicative October 2026 estimates — confirm locally before budgeting
Discuss your project