← All articles

Commercial & Hospitality · 09 Nov 2026 · 21 min read

Small Factory Shed Layout and Planning

Small Factory Shed Layout and Planning — cover

A factory shed is one of the few buildings where the contents must be designed before the building. A house can be planned as rooms and then furnished; a factory that is built first and fitted with machines later almost always ends up with the wrong column in the wrong place, a door too low for the tallest load, a floor that cracks under a press it was never told about, and a material flow that doubles back on itself across the shop. The shed is just a weatherproof clear-span box; what makes it a good factory is that the box was shaped around the process it has to hold.

Across Gujarat's industrial estates — Sachin, Pandesara, Hojiwala and hundreds of smaller GIDC plots — the same mistakes repeat. Owners fix the plot and the budget, build the biggest plain shed the money allows, and only then work out where the machines go. The result is a shed that is tall where it needs to be short and short where it needed to be tall, with a single small door for both incoming trucks and outgoing goods, no proper raw-material or finished-goods yard, and a floor poured to one thickness everywhere regardless of what stands on it. Every one of these is cheaper to fix on paper than in steel and concrete.

This article plans a small factory shed the right way round. It starts with the process flow and the machines, derives the clear span, bay spacing and height from them, then covers the structure, the floor and its loading, the lighting and ventilation that the National Building Code and the Factories Act require, the fire and escape routes, and the indicative costs. The numbers are for a small to medium shed of the kind an SME builds on a GIDC plot, not a large automated plant, and the prices are indicative October 2026 ranges to be confirmed locally before budgeting.

The industrial shed in India, briefly

The clear-span industrial shed is a twentieth-century idea that India adopted enthusiastically after independence, as industrial estates spread around every major city. The earliest sheds were built in load-bearing masonry with timber or steel trusses, which limited the clear span to what a truss could economically cross and filled the floor with columns. Rolled-steel trusses and later tubular trusses stretched the spans and opened up the floor. The decisive change, from roughly the 2000s onward, was the pre-engineered building (PEB): a tapered-portal steel frame designed and fabricated to the exact loads of the shed, shipped flat and bolted together on site. PEB made long clear spans, fast erection and predictable cost the norm, and today the great majority of new small-factory sheds in India are PEB, with reinforced-concrete sheds used where fire rating, vibration or a corrosive process makes steel less suitable.

Span, bay and height: the three numbers that define a shed

A shed is described by three dimensions. The clear span is the column-free width across the shed, set by how wide the process and its aisles are — a single production line with gangways might need 15 m, a two-line layout 20–30 m. The bay spacing is the distance between frames along the length, usually 5–8 m, chosen to balance steel weight against foundation count. The clear height is measured from the finished floor to the underside of the rafter (or to the bottom of a crane beam), and it is driven by the tallest machine, the lift of any travelling crane, and the stacking height of stored goods. Getting the height right matters because every extra metre adds wall and steel over the whole perimeter, while too little height means the crane cannot lift over a machine or the forklift cannot stack a third pallet.

Fig. 1 — Portal-frame shed section (dimensions in mm) clear span 20000 eaves 7000 9500 crane beam 6000 tapered PEB column roof slope 1:10 Clear span comes from the process width plus gangways; eaves height from the tallest machine, the crane lift and the stack height. Every extra metre of height adds cladding and steel around the whole perimeter, so size it, do not round it up.
Fig. 1 — Portal-frame shed cross-section: span, eaves and crane height (mm)
Shed useTypical clear spanBay spacingEaves heightNote
Light assembly / packing12–18 m5–6 m5–6 mForklift stacking 2–3 pallets high
General manufacturing (SME)18–24 m6–7.5 m6–8 mRoom for an EOT or jib crane
Heavy fabrication / machine shop24–30 m6–8 m8–10 mOverhead crane with good hook height
Warehouse / godown20–30 m7.5–9 m8–12 mHigh-bay racking drives the height
Textile / processing (common in Surat)15–24 m6–7.5 m5–7 mHumidity and lint control matter

Laying out the process: flow, zones and storage

A factory works well when material travels in one direction and never crosses its own path. The classic small-shed layout is a U or an L: raw material arrives at one point, moves through receiving and storage, then through the process line in sequence, past in-line quality checks, into finished-goods storage, and out through dispatch — ideally with incoming and outgoing on separate doors so a delivery truck never blocks a dispatch truck. Around this main flow sit the support functions: a small office and reception at the front, toilets and a canteen or rest area for workers, a store for tools and spares, and a space for the electrical panel and any compressor or utility plant, kept away from the clean process where possible.

Storage is usually underestimated. Raw material and finished goods both need defined areas, not whatever floor happens to be free, and both grow when production is busy. A common rule of thumb is to allow a quarter to a third of the shed floor for storage and movement and the rest for process, but the honest method is to count the pallets and the peak stock and draw the racking. Gangways must be wide enough for the handling equipment — about 3.5–4.0 m for a counterbalance forklift, 2.6–3.0 m for a reach truck — and a clear main aisle should run the length of the shed as both a material route and an escape route.

Fig. 2 — One-way process flow (dimensions in mm) RAWMATERIALreceiving PROCESS LINE A PROCESS LINE B / QC OFFICEand welfare FINISHEDGOODS DISPATCH main aisle / escape route overall length 42000 process bay 20000 22000 Material enters at one end and leaves at the other without crossing its own path. Incoming and outgoing use separate doors so trucks never block each other. The main aisle doubles as the primary escape route.
Fig. 2 — Small factory shed: one-way process flow and zones (plan, mm)
ElementTypical dimensionWhy
Truck / main shutter door4000–5000 mm wide, 4500 mm highPasses a loaded truck or tempo
Personnel door1000–1200 mm wideSeparate from the truck door for safety
Counterbalance forklift aisle3500–4000 mmWider turning circle
Reach-truck aisle2600–3000 mmNarrower, so more floor for process
Truck apron / manoeuvring yard12000–15000 mm deepLets a truck reverse to the dock
Office / welfare at the front10–15 % of shed areaReception, cabin, toilets, canteen
Mezzanine clear height (if used)2400 mm minimum each levelStores or offices over part of the floor

Floors, loading and services

The floor is the most heavily used and most expensive-to-repair surface in a factory, and it must be designed for what stands and moves on it. A light assembly shed may need only a 125–150 mm reinforced slab; a shed with forklifts and racking legs needs 150–200 mm with a hardened, dust-proof finish; a heavy machine shop with presses, lathes and impact loads needs a thicker slab, often with separate isolated foundations for vibrating machines so their shaking does not crack the surrounding floor. Modern sheds increasingly use vacuum-dewatered (VDF) or laser-screeded concrete floors with a trowelled hardener topping, which gives a flat, durable, low-dust surface that forklifts and racking need.

Services are planned as routes, not afterthoughts. A factory needs a dedicated electrical room with the main panel and distribution, cable trays or trenches feeding the machines, a compressed-air ring main if pneumatic tools are used, water and drainage to the process and the welfare block, and often an effluent route if the process is wet. Running these overhead on the structure keeps the floor clear, but the loads must be told to the structural designer so the frame can carry them. Natural daylight from roof lights and good artificial lighting over work positions reduce both the power bill and accidents.

Fig. 3 — Column grid and floor zones (dimensions in mm) heavy slab 200 mm (machines) general slab 150 mm (storage) bay 6000 bay 6000 span 20000 Vibrating machines sit on isolated foundations separated from the surrounding floor slab. Keep the column grid regular so bays repeat and foundations, purlins and cladding are standard. Tell the structural engineer every machine load, hung service and crane before the frame is designed — retrofitting loads onto a finished frame is costly.
Fig. 3 — Structural grid and floor zones (plan, mm)
Floor useSlab thicknessFinishDesign note
Light assembly, packing125–150 mm RCCTrowelled, sealedLow point loads; dust control for packing
Forklift and racking150–200 mm RCCVDF with hardener toppingFlatness matters for stacking
Heavy machine shop200 mm or moreHardener toppingIsolated foundations for vibrating plant
Wet / processing area150 mm with fallChemical-resistant, falls to drainBunding and effluent route
Office and welfare blockRCC + flooringVitrified tile or similarSeparate from the shop floor

Lighting, ventilation and worker welfare

A factory is a workplace, and Indian law treats it as one. The Factories Act and state factory rules, read alongside the National Building Code, set requirements for lighting, ventilation, drinking water, toilets, washing facilities and often a canteen and rest space once the worker count crosses thresholds. For the designer, the practical consequences are: generous natural light from roof lights or north-light glazing so the shop is not lit by electricity alone; cross-ventilation and ridge ventilators to clear heat, which builds up fast under a steel roof in an Indian summer; adequate separate toilets for men and women scaled to the headcount; clean drinking water points; and a welfare block that does not open directly onto a hazardous process.

Heat is the quiet enemy of an Indian shed. A bare profiled-steel roof radiates heat down onto the workers below, so roof insulation, a reflective roof coating, roof-mounted turbo or ridge ventilators and, where the process allows, air coolers or spot cooling at work positions make a measurable difference to both comfort and output. In Surat's textile and processing units, humidity and airborne lint add their own demands, sometimes needing humidity control and extraction. North-light roofs — the old saw-tooth form — are still an elegant answer where even, glare-free daylight matters.

Fig. 4 — Roof ventilation and daylight (section) span 24000 ridge ventilator daylight hot air rises and exhausts insulated, reflective roof sheet Hot air collects at the ridge and must be let out; a continuous ridge or turbo ventilator plus an insulated, reflective roof sheet keeps the shop floor far cooler than a bare roof. Roof lights or north-light glazing cut the daytime electricity bill.
Fig. 4 — Roof ventilation and daylight section (mm)

Fire safety, exits and compliance

A factory must be safe to leave and safe to fight a fire in. The National Building Code Part 4 governs fire and life safety: travel distance to an exit, the number and width of exits, fire-resistance of structure and compartments, and the fire-fighting provision — extinguishers, hydrants, hose reels and, for larger or higher-hazard sheds, sprinklers and a static water tank with a pump. The occupancy classification (industrial, and its hazard sub-class) decides how strict these are, and a process that stores or uses flammable materials attracts tighter rules. Beyond the building code, a factory typically needs consent to establish and operate from the state pollution control board, factory registration and plan approval, and electrical and sometimes boiler approvals — all best lined up early, because they can shape the layout.

Exits are a design input, not a label added at the end. A shop floor should have at least two separate exits remote from each other so a fire at one does not trap workers, the main aisle should lead to an exit, and doors on escape routes should open in the direction of travel. The time to plan this is while the layout is on paper, when moving a door costs nothing.

What a small factory shed costs

Shed cost divides into the land and site works, the structure and envelope, the floor, and the internal fit-out and services. The ranges below are indicative October 2026 figures for a small to medium shed and vary with location, specification, span and height; a tall, long-span, crane-carrying shed costs much more per square foot than a modest storage shed. Confirm every figure with local fabricators and contractors before budgeting.

ItemIndicative Oct 2026 rateNotes
PEB structure (supply and erect)₹55–85 per kg of steelDesign weight varies with span and height
Basic PEB shed, civil plus structure₹900–1,600 per sq ftModest span and height, simple floor
Better shed with crane and services₹1,600–2,800 per sq ftLonger span, crane beam, VDF floor
VDF / laser-screeded floor₹90–180 per sq ftWith hardener topping
Roof insulation and ridge ventilators₹40–90 per sq ft of roofCuts heat; pays back in comfort
Office and welfare block (fit-out)₹1,000–1,800 per sq ftFinished to a working standard
Electrical, lighting and services10–20 % of shed costHighly process-dependent

Where small factory sheds are going

Three trends are visible on new Indian industrial estates. The first is speed and standardisation: PEB and prefabricated welfare and office modules let a shed go up in weeks, and standard bay grids make it easy to extend later. The second is energy: rooftop solar on a large shed roof is now routine and often pays back within a few years, insulated and reflective roofs cut cooling load, and LED high-bays with daylight sensors have replaced the old metal-halide fittings. The third is flexibility and compliance: owners increasingly design the shed so the layout can be reconfigured as the product changes, and treat the pollution, fire and factory approvals as design inputs from day one rather than paperwork at the end. For a small owner, the lesson is to insulate the roof, wire for solar, keep the grid regular and leave room to grow.

Rules for planning a factory shed

  • Draw the process flow first — raw material in, one-way through the line, finished goods out on a separate door.
  • Derive the clear span from the process width plus gangways, and the height from the tallest machine, crane lift and stack.
  • Keep the column grid regular so bays, foundations, purlins and cladding repeat and stay cheap.
  • Tell the structural engineer every machine, crane and hung-service load before the frame is designed.
  • Match the floor slab and finish to the load: thin for assembly, thick with hardener for forklifts and machines.
  • Insulate the roof and add ridge or turbo ventilators — a bare steel roof bakes the shop floor.
  • Provide the lighting, ventilation, toilets, drinking water and welfare the Factories Act and NBC require.
  • Plan at least two remote exits and the fire-fighting provision on paper, while a door still costs nothing to move.

Frequently asked questions

These are the questions owners most often put to Aaditya Interior and to shed contractors when planning a small factory, with short practical answers.

What clear span and height does a small factory shed need?

For a small to medium shed, a clear span of 18–24 m with 6–7.5 m bays suits most single or twin production lines, and an eaves height of 6–8 m allows a light crane or two-to-three pallet stacking. A simple assembly or packing shed can be lower and shorter-span; a heavy machine shop with an overhead crane needs a longer span and 8–10 m of height. Always size the height from the tallest machine, the crane lift and the stacking height rather than rounding up.

Is a PEB shed better than an RCC shed?

For most small factories, yes. A pre-engineered steel building gives long clear spans, fast erection and predictable cost, and is easy to extend. A reinforced-concrete shed suits cases where a higher fire rating, heavy vibration, or a corrosive process makes steel less suitable, or where the owner wants a heavier, lower-maintenance structure. The process and the budget decide; PEB is the default for speed and span.

How thick should a factory floor slab be?

It depends on the load. A light assembly or packing shed may need only 125–150 mm of reinforced concrete, a shed with forklifts and racking needs 150–200 mm with a hardener finish, and a heavy machine shop needs 200 mm or more with isolated foundations for vibrating machines. A flat, dust-free finish such as a vacuum-dewatered or laser-screeded floor matters wherever forklifts and racking are used.

What approvals does a factory shed need in India?

Typically plan approval from the local or industrial development authority, factory registration and plan approval under the Factories Act, consent to establish and operate from the state pollution control board, and electrical and sometimes boiler approvals. Fire and life-safety provisions follow the National Building Code. The exact list varies by state and by the nature of the process, so it is best confirmed with a local consultant early, because the approvals can shape the layout.

How do you keep a steel-roof shed cool in Indian summers?

Insulate the roof sheet or add an air-gap and a reflective top coat, let hot air escape through a continuous ridge ventilator or roof-mounted turbo ventilators, and bring in cross-ventilation at low level. Roof lights or north-light glazing cut daytime electricity use, and spot cooling or air coolers at work positions help where the process allows. These measures together make a far bigger difference than fans alone against the heat radiating from a bare steel roof.

Sources & standards

  1. National Building Code of India 2016, Part 3 (General Building Requirements) and Part 4 (Fire and Life Safety)
  2. The Factories Act 1948 and state factory rules — lighting, ventilation, drinking water, toilets and welfare provisions
  3. Bureau of Indian Standards — IS 800 (general construction in steel) and IS 875 (design loads) for structural design
  4. Metal Building Manufacturers' practice and pre-engineered building design conventions (described generically)
  5. Neufert, Architects' Data — industrial buildings, loading and circulation data
  6. Central / State Pollution Control Board — consent to establish and operate for industrial units (general guidance)
  7. Price ranges: indicative October 2026 estimates — confirm locally before budgeting
Discuss your project